Technical Specification - Hallde VCM-41 Instrucciones De Uso

WARNING:
• Do not pour or spray water onto the machine.
• Do not use sodium hypochlorite (chlorine) or
any other agent containing this substance.
• Do not use sharp objects for cleaning or
any objects not intended for the purpose of
cleaning.
• Do not use abrasive detergents or cleaning
products.
• Avoid the use of cleaning sponges with
scouring pads (e.g. Scotch-Brite™).
ADVICE ON CARE:
• Clean the machine immediately after use.
• Dry the machine immediately after cleaning.
TROUBLE SHOOTING
FAULT: The mixer cannot be started, or stops
while in operation and cannot be restarted.
REMEDY:
• First, make sure that the scraper system,
lid and bowl is correctly assembled on the
mixer.
• Inspect the power connections.
• Inspect the fuse box. Check fuse rating and
if any other equipment shares the same fuse.
To prevent the mixer from overheating, the
mixer is fitted with two thermal switches (TCO).
One in the motor and one inside the chassis. If
a switch is triggered it will take around 10-30
minutes before the mixer can be restarted.
• Let the mixer cool down between batches.
The mixer is not designed for continuous
use.
If the mixer still can't be restarted, call in a
qualified service technician.
FAULT: Low capacity or poor cutting results.
REMEDY:
• Inspect the condition of the knives.
• Process a smaller amount.
• Pre-cut to 4x4x4 cm or less for optimum
result.
• Increase or decrease operating time.
• Use the scraper system for even cutting
result.

TECHNICAL SPECIFICATION

HALLDE VCM - 41
CAPACITY AND VOLUME: Gross volume
4 litres. Net volume liquid 1.6 litres.
MACHINE BASE: Motor: 0.55 kW, 100 V,
single phase, 50/60 Hz, 9/8 A. Motor: 0.55 kW,
110-120 V, single phase, 50/60 Hz, 8 A. Motor:
0.55 kW, 230 V, single phase, 50/60 Hz, 4.7 A.
Thermal motor protection. Transmission: direct
drive. Safety system: three individual safety
switches and mechanical motor brake. Degree
of protection: IP44. Plug: 10 A, earthed. Fuse
in fuse box for the premises: 10 A, delayed.
Sound level LpA (EN31201): 72 dBA. Magnetic
field: less than 0.1 microtesla.
4
CONTROLS AND SPEEDS: "0" = machine
switched off. "I" = machine runs continuously
at 1 500 rpm (50 Hz) or 1 700 rpm (60 Hz). "P"
(pulse) = machine runs at 1 500 rpm (50 Hz)
or 1700 rpm (60 Hz) until the knob is released.
BOWL VOLUME: Gross volume 4 liters. Net
volume liquid 1.6 liters.
NET WEIGHTS: Machine base: 14.8 kg.
Bowl complete with knife, lid and scraper
system: 1.6 kg.
KNIFE: The diameter of the chopping knife
is 190 mm.
NORMS/STANDARDS: NSF STANDARD 8,
see declaration of conformity.
TECHNICAL SPECIFICATION
HALLDE VCM - 42
CAPACITY AND VOLUME: Gross volume 4
litres. Net volume liquid 1.6 litres.
MACHINE BASE: Motor: 0.75 kW, 230 V, three
phase, 50 Hz, 2.5/2.0 A. Motor: 0.75/0.37 kW,
400 V, three phase, 50 Hz, 1.7/1.4 A. Thermal
motor protection. Transmission: direct drive.
Safety system: three individual safety switches
and mechanical motor brake. Degree of protec-
tion: IP44. Plug: 16 A, earthed. Fuse in the fuse
box for the premises: 10 A, delayed . Sound
level LpA (EN31201): 72 dBA. Magnetic field:
less than 0.1 microtesla.
CONTROLS AND SPEEDS: "0" = machine
switched off. "I" = machine runs continuously
at 1 500 rpm. "II" = machine runs continuously
at 3 000 rpm. "P" (Pulse) = machine runs at
1 500 rpm until the knob is released.
NET WEIGHTS: Machine base: 15.4 kg.
Bowl complete with knife, lid and scraper
system: 1.6 kg.
KNIFE: The diameter of the chopping knife
is 190 mm.
NORMS/STANDARDS: NSF STANDARD 8,
see declaration of conformity.
HALLDE • User Instructions