Important - Triton TMUTL Instrucciones De Uso

Selecting the right accessory
Task
Sawing
Sanding
Removing grout
Scraping
We recommend you purchase your accessories from the same store that sold you the multi-tool. Always use good quality accessories. Choose the type according to the task at hand. Refer to the
accessory packaging for more information.
Fitting the sanding pad & sanding sheets
1. Lift the Keyless Change Lever (4) and push forward (Fig. III) then loosen the Flange (12) by
rotating the lever anti-clockwise (Fig. IV). Rotating the Keyless Change Lever in a clockwise
direction will tighten the flange (Fig. IV)
Notes:
• If the accessory is open ended, the Flange can be loosened partially to fit the accessory
(Fig. V)
• If the accessory has a closed end, the Flange will need to be loosened and removed from
the multi-tool to fit the accessory (Fig. V) before re-inserting the Flange. A small amount of
finger pressure on the Flange is necessary when first tightening
• Sanding pad accessory will have the same mounting holes as a blade or scraper and the
same installation method will apply
2. Align the accessory holes with the buttons on the Flange (Fig. VII no. 1&2), hold the
accessory on the head, ensuring the buttons are aligned, and rotate the Keyless Change
Lever clockwise to tighten the Flange (Fig. IV)
Note: The accessory can be aligned with the buttons at the desired angle before tightening
the flange (Fig. VII no. 3).
3. Close the lever down to the lock position on the multi-tool (Fig. IX)
IMPORTANT: Ensure the locking tabs are facing the correct way when locking the lever. If
after tightening the flange the tabs are facing the wrong way (Fig. X), move the lever to the
middle position, then rotate the lever vertically until the tabs are facing the locking slots on
the multi-tool (Fig. X).
4. To remove the blade/accessory, repeat steps 1–3 and remove the sanding pad during step
2 (Fig. VII no. 1)
Pic
Bi-metal metal/wood end cut blade
HSS segment saw blade
Sanding base
Diamond-coated segment saw blade
Rigid scraper blade
5. Select the required sanding sheet for your intended task (see 'Selecting the right grade of
sanding sheet' below)
6. The sanding pad and sanding sheets use a hook and loop system for attachment. To mount
the sheet, line up one corner of the sheet with a corner of the sanding pad and gradually
push the rest of the sheet onto the pad, checking alignment as you do so, until the sheet is
fitted correctly (Fig. XI)
7. Firmly press the multi-tool with the installed sanding sheet against a flat surface and briefly
switch the tool ON. This provides good adhesion and prevents premature wear
Note: If one point has become worn after use, carefully pull off the sanding sheet, turn it 120°,
and re-install following steps 6 and 7.
Selecting the right grade of sanding sheet
• Sanding sheets are available in a variety of different grades: coarse (60 grit), medium (120
grit) and fine (240 grit)
• Use a coarse grit to sand down rough finishes, medium grit to smooth the work, and fine
grit to finish off
• Always use good quality sanding sheets to maximise the quality of the finished task
• It is advisable to carry out a trial run on a scrap piece of material to determine the optimum
grades of sandpaper for a particular job. If there are still marks on your work after sanding,
try either returning to a coarser grade and sanding the marks out before recommencing
with the original choice of grit, or try using a new piece of sandpaper to eliminate the
unwanted marks before progressing to a finer grit to finish the job
Name
Wood, plastic, fiberglass, nails, non-ferrous
metals, thin sheet metal, hardened fillers
Thin wood, plastic, fiberglass, non-ferrous
metals, thin sheet metal, hardened fillers,
window glazing
Wood, plastic, hardened fillers
Ceramic and stone tile, backerboard
Old paint, hardened adhesive, caulk, carpet
Application
GB
9