Initializing The Modes; Warning/Alarm Indications - Panasonic PV-GS19 Instrucciones De Operación

• For images not recorded with this Camcorder, the
size display is determined as follows according to
the number of horizontal pixels.
: 640 or more, less than 800 (The size is
not displayed at under 640 pixels.)
800 or more, less than 1 024
SVGA :
1 024 or more, less than 1 280
XGA
:
1 280 or more, less than 1 600
SXGA :
1 600 or more, less than 2 048
UXGA :
2 048 or more
QXGA
:
Photoshot Mode
(White):
While Photoshot recording is activated
(Red):
While the Card being read
(Green):
Using the card that cannot be
(Red):
recognized
To Display Date/Time Indication
This switches between date and time indications.
Set [ BASIC] or [ ADVANCE] >> [
>> [D/T], [DATE] or [OFF]. (pp. 23, 24)
• The Camcorder automatically records the date and
time of picture taking on the tape.
• You can also show or change the Date/Time
Indication by repeatedly pressing the [DATE/TIME]
Button on the Remote Control (PV-GS35 only).
To Change the Display Mode
Set [ SETUP] >> [
Set to [ON] and the display mode can be switched to
all functions. Set to [OFF] and it can be switched to
minimum display. (pp. 23, 24)
Progressive Photoshot
You cannot use the Progressive Photoshot Function in
the following cases.
When using Tape Recording Mode
• Digital Zoom [ ]
• 1/750 s or faster shutter speed
• When brightness is insufficient
• When the MagicPix Function is ON
• When the Portrait is used
• When the Gain Up mode is set to ON
When using Card Recording Mode
• When brightness is insufficient
• When the Gain Up mode is set to ON
Power Save Mode
Set [ SETUP] >> [
[5 MINUTES] or [OFF].
[OFF]:
When about 5 minutes passed without any operation,
the standby mode automatically will be set. In the
standby mode, [ ] blinks and it takes time more than
usual to start recording after you press the Recording
Start/Stop Button.
62
DATE/TIME]
DISPLAY] >> [ON] or [OFF].
POWER SAVE] >>
Others
[5 MINUTES]:
When about 5 minutes passed without any operation,
the Camcorder automatically turns off to protect the
tape or to prevent the battery from running down.
When you use the Camcorder, turn it on again.
• The Camcorder cannot be automatically turned off
when you connect the USB Cable or the DV Cable
with the Camcorder or when the Camcorder is in the
PC Mode.

Initializing the Modes

You can change the Menu settings back to the
shipping condition.
• Set to Tape/Card Recording Mode.
1
Set [ ADVANCE] >> [
[YES].
• The initializing takes a little while.
• Initializing will not erase a clock setting (p. 24) that
has been adjusted.

Warning/Alarm Indications

If any one of the following indications lights up or
flashes, please check the Camcorder.
Confirmatory Indications
A cassette with the accidental erasure
:
prevention slider placed in the [SAVE]
position is inserted.
No cassette is inserted.
The built-in battery is low. (p. 24)
[--] / :
The Warning/Alarm Indication appears
:
when you record yourself. Turn the LCD
Monitor towards the Viewfinder and check
the Warning/Alarm Indication.
No card is inserted.
:
REMOTE: An incorrect Remote Control mode has
been selected. (p. 15)
END : The tape came to the end during
recording.
The video heads are dirty. (p. 69)
:
Textual Indications
DEW DETECT/
Condensation has occurred. Take out the
cassette and wait for a while. It takes some time
until the cassette holder opens, but this is not a
malfunction. (p. 69)
TAPE END:
The tape came to the end during recording.
NEED HEAD CLEANING:
The video heads are dirty. (p. 69)
PUSH THE RESET SWITCH:
An irregularity in the equipment has been
detected. Press the [RESET] Button (p. 74). This
may solve the problem.
INITIAL SET] >>
EJECT TAPE: