TESY ES/GCVM 50 EC Instrucciones De Uso página 26

Explanations to Fig. 3:
EN
TS - thermal circuit breaker; TR - thermal regulator; R –
heating element; F - flange; АТ - anode tester (only for
models that have one); AP - anode protector;
VI. ANTI-CORROSION PROTECTION – MAGNESIUM
ANODE (FOR WATER HEATERS WITH WATER
TANKS COVERED BY GLASS-CERAMIC OR ENAMEL
COATING)
The magnesium anode provides additional protection
to the water tank's inner surface from corrosion. It is an
element undergoing wear and tear and is subject to
periodic replacement, which is at the expense of the user.
In view of the long-term and accident-free use of your
water heater, the manufacturer recommends periodic
inspections of the magnesium anode's condition by a
qualified technician and replacement whenever required,
and this could be performed during the appliance's
technical preventive maintenance.
For replacements, please contact the authorized service
centres or a qualified technician!
VII. OPERATION.
Switch on the electric water heater
1.
Before initial start of the appliance, please make sure
that the water heater has been correctly connected
to the electrical network and that it is filled up with
water. Switching on the water heater is done through
the device incorporated in the installation, which is
described in sub-item 3.2 of section V, or by inserting
the plug into an electrical socket (for models with cord
with a plug).
Description of the control panel of the appliance
2.
1 2
10 9
Description of buttons and elements:
1 – Button for switching on/off the appliance
2 – Button for switching between Manual mode and
Weekly programmer
3 – Button for reducing the set temperature or for
moving to the left during setting up
4 – Button for increasing the set temperature or for
moving to the right during setting up
5 – Button for locking the panel
6 – Button for enabling Vacation operation mode
7 – Multifunctional button for confirming the functions,
for choosing days of the week while setting up the
weekly programme, for changing the ON/OFF status of
the time zones while setting up the weekly programme
26
Instructions for using the built-in wireless communication module (Wi-Fi)
3 4 5
8 7 6
8 – LCD display
9 – Information button
10 – Button for selecting Eco Smart mode of operation
Switching on the electronic operation of the
3.
appliance
Switching on is done by pressing button
the display will show the mode which is to be used and,
depending on the type of mode, the symbols described
for each mode below.
Switching off the electronic operation is done by
pressing button .
Button is illuminated in various colours for the various
modes, as it follows:
•
White – in stand-by mode
•
Red – the appliance is switched on and is in heating
mode
•
Blue – the appliance is switched on and it has
reached the set temperature
This is valid for all modes described below.
Setting up and operation of the appliance
4.
•
Switching on and off the Wi-Fi module
Switching on and off the Wi-Fi module is done by
simultaneously pressing the buttons < and OK for
minimum 10 seconds in stand-by mode, i.e. when the
appliance is switched off from button
module is on, the display shows the following symbol
•
Setting the time and day of the week
In order for the programme modes to work properly you
must set the current time and day of the week. Setting
up is done in stand-by mode, i.e. when the appliance is
not switched on. Keep pressed the i button. First set the
day of the week using the arrows >, < and then confirm
by pressing the OK button. Then, set the hour and the
minutes again using the arrows >, < and the OK button.
•
"Manual operation" mode
By pressing the PROG button you can select Manual
operation mode. The display shows the symbol
mode the appliance works as an ordinary electrical water
heater, i.e. you are expected to set the temperature for the
water to be heated and then maintained. Afterwards the
appliance will operate every time the temperature of the
water is lower than the set value in order to reach it. When
you enable the Manual operation mode the display will
show both the symbol and the temperature of the water
in the electric water heater. To set the desired temperature,
use one of the arrows > and <. When you press them the
display will show the temperature as it is being set. The
temperature changes by 1°C each time one of the buttons
. By doing so
. When the Wi-Fi
.
In this