Adjusting The Footrest - Peg-Perego book Instrucciones De Uso

The hood may come with different features
depending on the collection chosen.
The hood may come with a clear viewing panel
offering UV protection, through which it is possible to
see the child (fig_b).
14 The hood can be adjusted to two positions (fig_ a).
Undo the zip (fig_ b) and stretch the fabric flap to see
the child and to let more air under the hood (fig_ c).
15 FOOT MUFF: To secure the foot muff to the stroller,
slide it under the front bar (fig_a) and attach the
rubber band with buttons (fig_b) to the side bars of the
stroller until it clicks into place (fig_c). Finally, fasten the
two stud buttons to the inner sides of the seat (fig_d).
16 RAINCOVER for complete Book:
to fit the rain canopy, extend it over the stroller and
snap fit the buttons on both sides of the hood (fig_a).
Fasten the elastic loops including the chassis in the
lower part of the stroller (fig_b).
• Do not use the rain canopy indoors and always make
sure that the child is not too hot.
• Do not place the rain canopy near heat sources and
pay attention to cigarettes.
• Make sure that the rain canopy does not interfere with
any moving mechanism of the stroller.
• Always remove the rain canopy before folding up the
stroller.
• Wash with a sponge and soapy water. Do not use
detergents.
17 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles of the waist strap (with attached shoulder
straps, arrow a) into the leg divider strap until they
click into place (arrow b). To unfasten them, press the
button which is situated in the centre of the fastener
(arrow c) and pull the waist strap outwards (arrow d).
18 To tighten the waist strap, pull on both sides in the
direction of the arrow. To loosen it do the opposite.
19 To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow a) until the
buckles are released and insert them in the backrest
loops (arrow b). Remove the shoulder straps from the
sack (arrow c) and insert them in the most appropriate
buckle (arrow d), then reattach the two buckles
behind the backrest (arrow e). The buckles are securely
attached when a click is heard (fig f).
WARNING: To fasten the belts in the third eyelet, lift the
fabric, as they are hidden in the lining.
20 ADJUSTING THE FOOTREST: the footrest can be adjusted
to 2 positions. To lower the footrest, push the two little
side levers downwards and lower the footrest at the same
time. To raise the footrest, push it upwards until it clicks.
21 ADJUSTING THE BACKREST: the backrest can be reclined
into 4 positions. To lower the backrest, lift the handle
and lower the backrest at the same time. Block it in the
desired position. To raise the backrest, lift the handle
and raise the backrest at the same time. Block it in the
desired position.
22 FRONT BUMPER BAR: to attach the front bumper bar
remove the protection caps (fig_a) and store them.
After removing the caps, insert the ends of the bumper
into the armrests until they click (fig_b).
23 The bumper bar can be opened on one side so an older
child can climb on and off more easily. To open the
bumper bar, push the button on the side and pull the
bar outwards (fig_a)
To remove the bumper bar, press the two buttons on
the sides and pull the bar outwards (fig_b).
When the bumper bar is off, replace the protection
caps onto the chassis armrests to close them.
24 COLLAPSING THE STROLLER: to collapse the stroller, put
the front wheels into fixed position, close the hood (if on
the stroller) and remove the car seat (if on the chassis).
- Align the handle with the stroller chassis as shown in
the picture (fig_a);
- lift the fastening hooks on the two sides of the chassis
(fig_b);
- Pull the interior handle placed behind the seat (fig_c)
and lift at the same time (fig_d).
25 then let the handle drop forwards until the stroller is
completely closed (fig_e).
Check that it has fastened to the closing hook on both
sides. If it has not, fasten the closing hook properly as
shown (fig_f).
The collapsed stroller is free standing.
To open the stroller, press on the frame and unfasten
the locking attachments on both sides (fig_g).
26 For greater compactness, it is possible to remove the
wheels.
To remove the rear wheels: pull the pivot outwards and
remove the wheel as shown in the figure (fig_a).
To remove the front wheels: press the tab as shown, and
remove the wheel (fig_b).
TRANSPORT: the stroller can be carried comfortably
locking the front wheels and grasping the main handle
(fig_c).
27 REMOVING THE LINING: to remove the stroller's lining:
- unthread the belt's leg divider from under the seat
(fig_a);
- slip the elastics off their hooks on both sides (fig_b);
28 - unscrew the belt on both sides, keeping your finger
under the bolt (fig_c);
- unfasten the lining from the armrests as shown in the
picture (fig_d);
- unfasten the soft cover from the seat (fig_e);
29 - on the back of the pushchair:
- remove the lining from the seat (fig_f);
- Unbutton the cover from both sides (fig_g);
- undo the buttons on both sides on the backrest (fig_h);
30 Unfasten and remove the shoulder straps from the
backrest as shown in the figure 19_a / 19_b;
- push in the openings and pull off the side lining.
Do this on both sides (fig_i);
- remove the lining from above (fig_l).
REPLACING THE LINING: to put the lining back on:
- fit the lining onto the backrest
- fit the lining over the platform
- attach the side elastics (27b)
- fasten the lining's hooks to the armrests (28d)
- fasten the lining's buttons to the chassis (28e)
- fasten the belt in the right position with the screwdriver
(28c)
- attach the leg divider under the seat. One part must be
above the seat and one below (27a)
- attach the belt at the desired height (point 19)
31 on the back of the stroller:
- insert the two rigid flaps between the tube and the seat
(fig_a);
- Button the cover back on, on both sides (fig_b)
32 Button the lining onto the stroller's backrest (fig_c).
Insert the rigid strap into its grooves until it clicks into
place. Check it is securely fastened by pulling it (fig_d).
GANCIOMATIC SYSTEM
The Ganciomatic System is the quick practical system
that enables you to attach the Primo Viaggio (0+ group)
car seat to the stroller in just one step.
33 Before attaching the car seat, you must:
- insert the stroller's break;
- put the backrest into the lowest position (flat, fig_a);
- lift the soft cover as shown in the figure (fig_b);
- lift the Ganciomatic attachments from the chassis (fig_c);
- put the car seat in mum-facing position and push it
down until it clicks (fig_d);
- Check that the child transport system is properly
fastened.
- Lift the stroller backrest to the highest position.
- Important: do not remove the bumper bar from the
stroller when you attach the car seat (read point 21 to
see how to attach the bumper bar).
- To release the car seat, read the car seat's instruction
manual.
34 To lower the stroller's Ganciomatic fittings, move them
inwards and rotate them downwards.
- 19 -