Assembly - Power Stroke PS907000 Serie Manual Del Operador

UNPACKING
This product requires assembly.
 Carefully cut the box down the sides then remove the
machine and any accessories from the box. Make sure
that all items listed in the loose parts list are included.
NOTE: This machine is heavy and requires a minimum of
two people to lift. To avoid back injury, lift with your legs
and not your back.
WARNING:
Do not use this product if any parts on the Loose Parts
List are already assembled to your product when you
unpack it. Parts on this list are not assembled to the
product by the manufacturer and require customer instal-
lation. Use of a product that may have been improperly
assembled could result in serious personal injury.
 Inspect the unit carefully to make sure no damage oc-
curred during shipping.
 Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
 If any parts are damaged or missing, please call
1-877-617-3501 for assistance.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not attempt to operate the generator until assembly
is complete. Failure to comply could result in possible
serious personal injury.
LOOSE PARTS LIST
See Figure 2
The following items are included with the generator:
Key
No. Description
1 Bolt (1/4-20 x 1-1/2 in.) ................................... 2
2 Rubber Foot .................................................... 2

ASSEMBLY

Key
No. Description
3 Washer (1/4 in.) ................................................ 2
4 Lock Nut (1/4-20) ............................................. 2
5 Frame Support ................................................ 1
6 Bolt (5/16-18 x 1 in.) ........................................ 2
7 Large Washer (5/16 in.) .................................... 4
8 Lock Nut (5/16-18) ........................................... 4
9 Wheel ............................................................... 2
10 Battery Maintainer ........................................... 1
11 Engine Lubricant.............................................. 1
12 Lanyard ............................................................ 2
13 Handle Lock Pin .............................................. 2
14 Handle ............................................................. 2
15 Bolt (5/16-18 x 2-1/4 in.) ................................. 2
16 Washer (3/8 in.) ................................................ 2
17 Handle Bracket Spacers.................................. 2
18 Small Washer (5/16 in.) .................................... 4
*19 Bolt (3/8-16 x 4-1/4 in.) ................................... 2
*20 Spacer (.38 ID) ................................................. 2
*21 Lock Nut (3/8-16) ............................................. 2
*22 Axle ................................................................. 2
*23 Hitch Pin .......................................................... 2
Operator's Manual (not shown) ....................... 1
*Your model will either include items 19, 20, and 21 OR items 22 and 23.
TOOLS NEEDED
See Figure 3.
The following tools (not included or drawn to scale) are
needed for assembly:
 8 mm, 11 mm, 13 mm, and 14 mm Socket Wrenches and/
or Combination Wrenches
 Phillips Screwdriver
NOTE: Do not put fuel or lubricant in the generator before
installing the feet, frame support, and wheels.
INSTALLING FEET ON THE FRAME SUPPORT
See Figure 4.
 Locate the following items:
2 rubber feet
2 lock nuts (1/4-20)
2 washers (1/4 in.)
2 bolts (1/4-20 x 1-1/2 in.)
 Insert bolt through foot, then through frame support as
shown.
 Thread washer over the bolt, then install lock nut. Tighten
nut securely.
NOTE: Be careful not to overtighten so that foot material
collapses.
Qty.
 Repeat with remaining foot.
Page 11 — English
Qty.