Using Dsp Modes - JVC RX-ES1SL Manual De Instrucctiones

Creating realistic sound fields
1
CENTER* : To adjust the center speaker output level
(from –10 dB to +10 dB).
SURR L* 1 : To adjust the left surround speaker output level
(from –10 dB to +10 dB).
1
SURR R* : To adjust the right surround speaker output level
(from –10 dB to +10 dB).
2
PANORAMA control* :
• Select "ON" when you would like to enjoy
"wraparound" sound effect with side-wall image.
• Select "OFF" when you would like to hear
originally recorded sound.
* 1 "0" is the initial setting for each speaker setting.
* 2 "OFF" is the initial setting.
6
Turn MULTI JOG to adjust the item selected in
step 5 , then press SET.
Your setting is stored.
• When adjusting the speaker output levels, make adjustments so
that the sound level of the selected speaker is set at the same
level as that of the front speakers.
PL ΙΙ
L R
LPCM
SUBWFR
Ex.: When selecting "+8 (dB)" for "CENTER."
7
Repeat steps 5 and 6 to adjust the other
settings.
To cancel Surround mode
Press SURROUND repeatedly on the remote control or press
SURROUND then turn MULTI JOG on the front panel so that
"STEREO" appears on the display.
• If Surround mode is canceled while playing back multi-channel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer if you have connected a
subwoofer and set the subwoofer setting correctly—"USE" for Quick
Setup or "YES" for Manual Setup—see pages 17 and 18).
NOTES
• You can adjust the speaker output levels using the remote control
without outputting the test tone.
• You cannot adjust the center speaker output level and no test tone
comes out of the center speaker when "CNTR SP" is set to "NO."
• You cannot adjust the surround speaker output levels and no test
tone comes out of the surround speakers when "SURR SP" is set
to "NO."
• Remember not to change the speaker setting while using any
Surround modes; otherwise, the Surround mode may be canceled
when you deactivate the speakers required for it .
• You cannot use any Surround modes when selecting DVD MULTI
as a playback source.
30

Using DSP modes

Once you have adjusted the DSP modes, the adjustment is
memorized for each source.
• You cannot use the DSP modes if no surround speakers are
connected.
• You cannot adjust the effect level for "ALL CH ST."
When operating this receiver using the
remote control, always set the mode
selector to AUDIO/TV/VCR/DBS.
Before you start, remember...
Make sure that you have set the speaker information correctly (see
pages 16 to 19).
From the remote control:
KARAOKE SOUND BASS TREBLE
ZOOM 1 2
BASS TREBLE
4 5
VFP
KARAOKE
7 8
KEY TV RETURN
ANGLE 10 0
KEY VOCAL EFFECT
REPEAT 3D
DIMMER SLEEP ANALOG/DIGITAL CANCEL
INPUT
SMART S. SETUP BASS BOOST A.POSITION
TONE
SURROUND
TEST EFFECT DECODE
VOL
SUBWFR CENTER L SURR
1
Start playing 2 channel software—either Linear
PCM or analog signal—and select the source.
2
Press SURROUND repeatedly until one of the
DSP modes you want to apply appears on the
display.
The DSP indicator lights up on the display.
• Each time you press the button, the DSP modes change as
follows:
L R
LPCM DSP
SUBWFR
PLII MOVIE
LIVE CLUB
HALL
ALL CH ST.
(Back to the beginning)
3
Press TEST to check the speakers output
balance.
"TEST L" starts flashing on the display, and a test tone comes out
of the speakers as follows:
L R
LPCM
SUBWFR
TEST L
(Left front speaker)
TEST LS
(Left surround speaker)
3
It will be convenient for you to use
6
the remote control for the sound
9
adjustments, since you can make
+
100
+10
adjustments from your listening
point, and use the test signal.
R
PLII MUSIC
DANCE CLUB
PAVILION
STEREO
(Surround/DSP off)
DSP
TEST C
(Center speaker)
(Right front speaker)
TEST RS
(Right surround speaker)
VOL
VOL
TEST R