Turning Off The Sounds Temporarily-Muting; Turning Off The Power With The Sleep Timer; Changing The Display Brightness - JVC RX-ES1SL Manual De Instrucctiones

Turning off the sounds temporarily—
Muting
From the remote control ONLY:
Press MUTING to turn off the sound through all
connected speakers.
"MUTING" appears on the display and the volume turns off (the
volume level indicator goes off).
ANALOG
L R
SUBWFR
To restore the sound, press MUTING again.
• Pressing VOLUME +/– (or turning MASTER VOLUME control on the
front panel) also restores the sound.
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and the shut-off time
changes in 10 minutes intervals.
SLEEP indicator
ANALOG L R SLEEP
SUBWFR
20
10 30
0
(Canceled)
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly until "SLEEP 0" appears on the display. (The
SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.

Changing the display brightness

You can dim the display.
Press DIMMER repeatedly.
• Each time you press the button, the indication changes as follows:
DIMMER 1: • Dims the display slightly.
• Dims the blue indication lighting source lamps.
DIMMER 2: • Dims the display more than DIMMER 1.
• Dims the blue indication lighting source lamps
(same as DIMMER 1).
DIMMER 3: Turns off the display and the blue indication
lighting source lamps.
DIMMER OFF: Cancels the dim (normal display).
VOL
50 60
40
70
90 80
NOTES
• When setting speakers and basic items or adjusting sound, select
"DIMMER OFF" to confirm the setting you make on the display.
• When selecting DVD or DVD MULTI as a source using the remote
control, DIMMER functions for the DVD player. To dim the display
and indication on the receiver, select a source except DVD or DVD
MULTI on the remote control, and then press DIMMER.
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power,
• when you change the source, and
• when you change the analog/digital input mode (see page 13).
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analog/digital input mode (see page 13)
• Tone adjustment (see page 22)
• Subwoofer output level (see page 22)
• Bass boost (see page 23)
• Input attenuator mode (see page 23)
• Balance (see page 23)
• Subwoofer audio position (see page 23)
• Surround/DSP mode selection (see pages 26 – 31)
NOTES
• If the source is FM or AM, you can assign a different setting for
each band.
• You cannot assign and store different settings for digital input
mode and analog input mode.
Signal and speaker indicators on the display
Signal indicators
L C R
ANALOG L
LPCM
LFE
SUBWFR LFE
DOLBY D
LS
DTS
LS S RS
The following signal indicators light up —:
L: • When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R: • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LS: Lights up when the left surround channel signal comes in.
RS: Lights up when the right surround channel signal comes in.
S: Lights up when the monaural surround channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
The speaker indicators light up as follows:
• The subwoofer indicator ( SUBWFR
set to "USE" for Quick Setup (see page 17) or to "YES" for
Manual Setup (see page 18).
• The other speaker indicators light up only when the
corresponding speaker is set to "SML" or "LRG," and also when
required for the current playback.
Basic operations
Speaker indicators
L C R
PL ΙΙ
C R
DSP HP
SUBWFR
AUTO SR
S RS
INPUT ATT
LS RS
) lights up when "SUBWFR" is
15