Setting The Remote-Controllable Input; Setting The High-Definition Signal Types - JVC GM-V42PCE Manual De Instrucciones

Setting the Remote-Controllable Input

When connecting the external control unit to the REMOTE
MAKE terminal, you need to set the desired input to use,
which you can select from the connected external control unit.
• For GM-V42PCE, GM-V42PCEG and GM-V42PCEB:
You cannot use this function unless the video input unit
(IF-C42P1G) is separately purchased and installed.
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding 2 to display
the Setup Menu.
S E T - U P M E N U
Cursor (3)
S T A T U S D I S P L A Y
C O N T R O L L O C K
R E M O T E S W I T C H
H D S I G N A L M O D E
W H I T E B A L A N C E
T I M E R
A D J U S T :
2
Press 5/∞ to move the cursor (3) to
"REMOTE SWITCH."
• The Setup Menu consists of two pages. If you keep
pressing 5/∞, you can move to the other page from
the current page.
3
Press 2/3 to select the desired setting.
Each time you press the button, the Remote Switch
Mode changes as follows:
MODE1: Input alternates between "VIDEO A" and
"VIDEO B" when controlled from the external
control unit.
MODE2: Input alternates between "VIDEO A" and
"RGB B/COMPO." when controlled from the
external control unit.
MODE3: Input alternates between "VIDEO A" and
"RGB A" when controlled from the external
control unit.
MODE4: Input alternates between "VIDEO B" and
"RGB B/COMPO." when controlled from the
external control unit.
MODE5: Input alternates between "VIDEO B" and
"RGB A" when controlled from the external
control unit.
MODE6: Input alternates between "RGB B/COMPO."
and "RGB A" when controlled from the
external control unit.
4
Press MENU/EXIT (or MENU on the
Monitor) once to exit from the menu
operations.
1 / 2
: O F F
:
O F F
* 1
: M O D E 1
: 1 0 8 0 i
S E L E C T : E X I T :
M E N U

Setting the High-Definition Signal Types

You can select one of the High-Definition (HD) signal types
through the COMPONENT/RGB B terminals — 1080i or
1035i. Normally set it to "1080i."
• Without setting "RGB/COMPO." correctly, you cannot
show any picture though you select the COMPONENT
input (see page 22).
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding 2 to display
the Setup Menu.
S E T - U P M E N U
Cursor (3)
S T A T U S D I S P L A Y
C O N T R O L L O C K
R E M O T E S W I T C H
H D S I G N A L M O D E
W H I T E B A L A N C E
T I M E R
A D J U S T :
2
Press 5/∞ to move the cursor (3) to
"HD SIGNAL MODE."
• The Setup Menu consists of two pages. If you keep
pressing 5/∞, you can move to the other page from
the current page.
3
Press 2/3 to select the desired setting.
Each time you press the button, the HD signal type
alternates between "1080i" and "1035i."
• You can select either "1080i" and "1035i" according to
the HD signal you input — whichever gives you
proportionally shaped pictures.
4
Press MENU/EXIT (or MENU on the
Monitor) once to exit from the menu
operations.
1 / 2
: O F F
: O F F
* 1
: M O D E 1
: 1 0 8 0 i
S E L E C T : E X I T : M E N U
27