Noise And Vibration - Flex LE 9-11 125 Instrucciones De Funcionamiento Originales

L 9-11 125/LE 9-11 125/L 12-11 125/L 15-11 125/LE 15-11 125/L 1400 125
Support panels or any oversized workpiece to minimi-

ze the risk of wheel pinching and kickback. Large work-
pieces tend to sag under their own weight. Supports must
be placed under the workpiece near the line of cut and near
the edge of the workpiece on both sides of the wheel.
Use extra caution when making a "pocket cut" into exi-

sting walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
Additional safety instructions
The mains voltage and the voltage specifications on the ra-

ting plate must correspond.
Do not press the spindle lock until the grinding tool stops.


Noise and vibration

NOTE
Values for the A-weighted sound pressure level and for the
total vibration values can be found in the table on page 5.
The noise and vibration values have been determined in accor-
dance with EN 60745.
CAUTION!
The indicated measurements refer to new power tools. Daily
use causes the noise and vibration values to change.
NOTE
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure. The de-
clared vibration emission level represents the main applications of
the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level over
the total working period.
However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may dif-
fer. This may significantly decrease the exposure level over the to-
tal working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
CAUTION!
Wear ear protection at a sound pressure above 85 dB(A).
Overview (Figure A)
Different electric power tools are described in these instructi-
ons. The illustrated electric power tool may differ in detail from
the one which you purchased.
1 Spindle
2 Threaded flange
a Clamping nut
b Clamping flange
3 Guard hood
Can be adjusted without a tool through 360° by means
of 12 notches.
4 Handle
Handle can be fitted to the left or right.
(L 15-11 125, LE 15-11 125: handle with integrated pin
wrench)
5 Spindle lock
Secures the spindle when the tool is changed.
6 Gear head
With air outlet and direction-of-rotation arrow.
7 Switch rocker
Switches the power tool on and off.
With notched position for continuous operation.
8 Rear handle
9 Dial for preselecting the speed (LE 9-11 125,
LE 15-11 125)
10 4.0 m power cord with plug
11 Rating plate (not illustrated)
12 Face spanner
Instructions for use
WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
Before switching on the power tool
Unpack the angle grinder and check that there are no missing
or damaged parts.
Attach the guard (Figure B)
WARNING!
When using the angle grinder for roughing or cutting, never work
without the guard.
A special cutting guard must be used for cutting.
Pull out the mains plug.

Attach the guard (1.). Lugs on the guard hood must be

located in the flange recesses (2.).
Turn guard hood clockwise.

Rotation is possible in one direction only!
Remove in reverse order.

Attach the handle (Figure C)
NOTE
It is not permitted to operate the electric power tool without the
handle.
Attaching/changing the tool
Pull out the mains plug.

Attach the grinding wheel (Figure D)
Press and hold down the spindle lock (1.).

Using the face spanner, loosen the clamping nut on the

spindle in an anti-clockwise direction and remove (2.).
Handle (L 15-11 125, LE 15-11 125)
Figure E:
Remove the handle from the power tool by rotating it in an

anti-clockwise direction.
Rotate the cover on the handle by 180° until it engages.

Figure F:
The stop key is released.

Press and hold down the spindle lock (1.).

Figure G:
Using the stop key, loosen the clamping nut on the spindle

in an anti-clockwise direction and remove (2.).
Insert the grinding wheel in the correct position.

Screw the clamping nut with flange face up, onto the spindle.

Press and hold down the spindle lock.

Tighten the clamping nut with the pin wrench or stop key.

Carry out a test run to check that the tool is clamped in the

centre.
Test run
Insert the mains plug into the socket.

13