EdilKamin CALGARY Instalación Uso Y Mantenimiento página 39

Ocultar thumbs Ver también para CALGARY:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 68
Shutdown
While the boiler is working pressing the 0/1 key for 2 seconds
begins the shutdown process and "OFF" is displayed (for 10
minutes).
The turning off phase includes:
-The interruption of falling pellets
-The circulation of running water.
Never pull the plug during shutdown.
N.B. Please note that the circulator runs until the water tempe-
rature drops below 40° C.
Setting the clock
Press the MENU button for 2 seconds and use the + and – keys
to follow the instructions given on the display to access the
'Clock' menu.
This allows you to set the time on the electronic control board.
Then press MENU and the following data appears in sequence
– this can be adjusted: day, month, year, hour, minutes, day of
the week. When 'Save?' appears on the display, you can check
that the settings have been entered correctly before confi rming.
Press MENU to save the information ('Save OK' then appears
on the display).
Programmer to ignite and shutdown the boiler at various
times during the week.
Press the MENU button for 2 seconds to access the time setting
function and press the + key to access the weekly timer fun-
ction 'Program ON/OFF' will appear on the display.
The timer allows you to set a number of ignitions and
shutdowns per day (up to a maximum of three), for each day
of the week. As you confi rm via the MENU button, one of the
following options will appear:
- No Prog. (no program is set)
- Program/daily (a single program is set for every day)
- Program/weekly (a program is set for each day of the week)
Move from one to the other using the + and – keys.
Use the MENU button to confi rm the 'Daily program' option
and access the selection of the number of programs (ignition/
shutdown) to be set per day.
Use the 'Program/daily' option to set the identical program/s
for every day of the week.
The following will be displayed if the + key is pressed:
- No Prog.
- Prog. No. 1 (one ignition and one shutdown per day), Prog.
No. 2 (same as before), Prog. No. 3 (same as before)
Use the button to show them in reverse order. If the 1st pro-
gram is selected, the ignition time is shown.
The display shows: 1 Ignition Hour 10.30; use the +/– keys to
change the hour and press MENU to confi rm.
The display shows: 1 Ignition Minutes 10.30; use the +/– keys
to change the minutes and press MENU to confi rm.
In the same way, adjust the shutdown times.
The program is confi rmed by pressing the MENU button when
"Saved" appears on the display.
When confi rming 'Program/week', you will need to choose the
day to which the program is to apply:
1 Mon; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sat; 7 Sun
Once you have chosen the day by scrolling through them with
the + and – keys, confi rm by pressing MENU and proceed with
the settings of the programs in the same way as for the 'Pro-
gram/daily', selecting whether or not to enable a program for
INSTRUCTIONS FOR USE
- 39
each day of the week and choosing the number and times of
interventions.
Should you make a mistake whilst setting the programs you
can exit without saving by pressing the 0/1 key and 'Saved'
will appear on the display.
Should the hopper run out of pellets, the boiler will block and
'Stop Flame' will appear.
Pellet reserve warning
The boiler are equipped with an electronic pellet detection
system.
The pellet detection system is integrated into the electronic
control board, allowing the stove to monitor how many kilos of
pellets are left.
This verifi cation is implemented at any point whilst the stove is
in operation mode.
For correct system operation, it is important that the following
procedure is adhered with during the fi rst ignition (that must be
implemented by the DEALER).
Before starting to use the pellet detection system, you must
load and consume a full sack of pellets.
This allows for a brief running-in of the loading system.
Subsequently load 15 kg of pellets.
Then press the 'reserve' button once, thereby storing the
data into the memory that 15 kg have been loaded.
From now on the display will show the remaining pellets as
they decrease in kg (15...14...13). Each time pellets are reloa-
ded you must enter the quantity.
E.g. when loading 15 kg, simply press the 'pellet load' button
to enter this into the memory.
For other quantities, or in the event of an error, you can specify
the quantity using the pellet reserve menu as follows:
Press the MENU button for 2 seconds to view the SETTINGS.
Press + or – consecutively to view T. Max exit.
Confi rm by pressing MENU and the remaining quantity of
pellets will be displayed + that being loaded (default is 15 and
can be changed using the +/- keys).
Should the hopper run out of pellets, the boiler will block and
'Stop/Flame' will appear.
-

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Orlando

Tabla de contenido