Troubleshooting; Stereo Receiver - Jacuzzi J-210 Manual De Instalación

Troubleshooting

If the spa is not working the way it should, please first review
all the installation and operating instructions in this manual and
check the message on the panel display. If you are still not sat-
isfied it is working properly, please follow the troubleshoot-
ing instructions provided.
None of the components are working (pump, light)
Is there power to the spa?
Is the household circuit breaker tripped?
I
Contact an authorized Jacuzzi Service Centre.
Pump does not operate but light does
I
Press the "JETS" key. If the water remains still, check the le-
vel and make sure the spa is plugged in. If the problem persi-
sts, contact an authorized Jacuzzi service centre.
The main pump operates but no water flows from the jets.
Pump may not be properly primed.
This can happen after the spa is drained and refilled.
I
Press the JETS 1 button several times, never leaving the mo-
tor on for more than 5 to 10 seconds at a time.
Disconnect the power supply and unscrew the plug of the devi-
ator valve to let the air out and/or remove the filter. Ensure that
the deviator valve has been tightened and/or that the filter has
been re-installed before re-connecting the spa to the power
supply, then re-start the pump.
Poor jet action.
I
Press the JETS 1 button to make certain the pump 1 is on.
I
Place the air control in the "on" position.
I
Check that filter is not dirty and clean as necessary.
I
Make sure jets are fully open.
Water is too hot
I
Reduce temperature setting.
Water is too cold
I
Check temperature setting.
I
Keep the spa cover in place while heating.
I
Check the settings to see if your spa is in economy mode (see
chapter "Filter cycles").
If the problem persists in spite of these checks, contact your re-
tailer or an authorized Jacuzzi service centre.

Stereo receiver

(only for models J-230/J-270/J-280)
1
MUTE
PWR
EQ/LD
SEL
1
2
INT
8 9 10 11
1. On/off button: press the PWR (power) button to turn the
unit on and off.
2. Equalizer button: repeatedly press the EQ/LD button to se-
lect the various sound equalizing options: DSP Off, Jazz, Pop,
Classic, Rock or Vocal. Press and hold the EQ/LD button for two
seconds to activate/deactivate the "LOUD" function.
3. Mute Button: press the Mute button to deactivate the au-
dio. Press the key again to restore the previous volume level.
4. Open button: press the Open button to open the front pa-
nel. Insert a CD in the slot, pressing delicately (DO NOT USE
FORCE). Always remember to close the front panel to prevent
damage to the unit.
Note: Never insert a damp or wet CD as this may damage the
reading mechanism and void the manufacturer's guarantee.
5. A/PS button: lets you search for and memorize stations.
The tuner searches for stations, waits for a few seconds and then
continues the search. When the desired station is found, press
A/PS again to stop the search. To automatically search for and
memorize the stations with the strongest signal, pres and hold
the button for a few seconds and then release it.
1
MUTE
PWR
EQ/LD
SEL
1
2
INT
8 9 10 11
6. DISP button: lets you change between clock display and di-
splay of the radio station frequency. Once selected, the clock is
displayed for 5 seconds, after which the frequency of the sta-
tion reappears.
29
4 5 6
OPEN
A/PS
DISP
AQUATIC
6
5
3 4
UP
DN
RPT RDM
12 13 14 15
4 5 6
OPEN
A/PS
DISP
AQUATIC
6
5
3
4
UP
DN
RPT RDM
12 13 14 15
7
SOURCE
BND
16 17
7
SOURCE
BND
16 17