Radio Transmitter Self Learning With Receiver On Board Of Control Unit; Delete Transmitters - SEA USER 2-24V DG Manual Del Usuario

Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
RADIO TRANSMITTER SELF LEARNING
WITH RECEIVER ON BOARD OF CONTROL UNIT
! !
WARNING: Make the radio transmitters programming before you connect the antenna and insert the receiver into the
special CMR connector (if available) with turned off control unit. (The control unit automatically recognizes if the receiver is a RF, RF
Roll, RF Roll Plus or RF UNI module).
With RF Roll or RF Roll Plus module it will be possible to use only Coccinella Roll or Coccinella Roll Plus radio transmitters. or Smart
Dual Roll or Smart Dual Roll Plus.
With the RF UNI module it will be possible to use both the transmitters of the Roll Plus series and those with fixed code. The first
memorized transmitter determines the type of the remaining radio transmitters.
TrS
Select through the display
button (it is possible to associate max. 2 commands) and press OK to confirm the choice, now press the button of the radio transmitter which
you want to associate. If the storage is successful, the display will show
If the receiver is a Rolling Code, press twice the button of the radio transmitter that you want to program to memorize the first TX.
TrS
In the MENU it is possible to select Strt (to associate a Start command), StPd (Pedestrian Start ),
on the EXP output), StoP (To associate the STOP command to the TX), dEL. (To delete all TX), del. s (To delet the single transmitter only if it is a
Rolling Code Plus).
Notes:
- Enter radio transmitters learning only when the working cycle stops and the gate is closed.
- If the radio transmitters are Rolling Code it's possible to memorize up to 800 codes (buttons).
- If the radio transmitters are with fixed code it will be possible to memorize up to max. 30 codes (buttons).
- You can store max. 2 of the available 4 functions. If the control unit receives a code which was already associated to another function it will be
updated with the new function.
DELETE TRANSMITTERS FROM THE RECEIVER
With modules different from RF UNI, it will be possible to delete only the entire memory of the receiver.
Proceed as follows: select from the menu
With the RF UNI module, it will be possible to also delete the single button of the transmitter.
It can be done in two ways:
1) If you have the transmitter, or if you are using transmitters with fixed code, the cancellation can be executed by simply retransmitting the
code. Ex. Button 1 of the transmitter memorized as START; access the menu
Send a STRT command from the transmitter and on the display will show DEL.
At this point the single button results deleted.
2) If you do not have a transmitter, or you are using a Roll Plus transmitter, you can delete the transmitter selecting the serial number of the
transmitter to be deleted.
Procede as follows: Access the menu
DOWN buttons, press OK, check on the display if the serial number of the transmitter to be deleted is the right one, press OK, on the display
shows SURE, if the transmitter to be deleted is the right one press OK, otherwise press the DOWN button to return to the menu
Note: When using Roll Plus transmitters, it is recommended to record on a table similar to the below example, the serial number associateding
it to the memory location where it was stored.
TABLE
Memory
EXAMPLE location
67410756
®
and press OK, now select with the UP and DOWN buttons, the command to which you want to associate the
TrS
DEL and hold the OK button until the display shows the message DONE.
TrS
, press OK, select DELS, press OK, choose the memory location to be deleted through the UP and
Transmitter
button
1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
English
E
.
TrS
2 3 4
REV 04 - 03/2013
USER 2 - 24V DG
. E st
press OK, select STRT, press OK.
Serial number Customer
(For the activation of a contact
TrS
.
37