Instalation; Transport And Discharge; Arrangement Of The Lighting System; Arrangement Of The Pneumatic System - Sagola S25 Manual De Instrucciones

INCORRECT INSTALLATION OF THE MACHINE
MAY CAUSE DAMAGE TO PEOPLE, ANIMALS OR
OBJECTS. THE MANUFACTURER CANNOT BE
CONSIDERED RESPONSIBLE FOR THESE DAMA-
GES.

7.1 TRANSPORT AND DISCHARGE

The equipment Aquaplastic is delivered packa-
ged. It must be transported and stored according
to the indications on the packaging.
Due to the low weight of the equipment Aqua-
plastic can be moved by two people without
using other means.

7.2 ARRANGEMENT OF THE LIGHTING SYSTEM

The Client must make sure that there is suitable
lighting for the surroundings and that the lighting
conforms to the regulations in force. In particular,
the Client must arrange the positioning of lighting
that illuminates all the working area.

7.3 ARRANGEMENT OF THE PNEUMATIC SYSTEM

The Client must arrange a line of filtered com-
pressed air supplied by a compressor that is
suitable for the consumption required. Do not use
compressed air that contains chemical products,
synthetic oil with organic solvents, salts or corro-
sive gases as they can cause damage or malfunc-
tioning. The line of compressed air must arrive up
to the supply points of the machine. If the com-
pressed air contains a large amount of moisture,
it may cause malfunctioning in the valves and in
the pneumatic components. Install a moisture
separator downstream from the compressor to
avoid this.
7.4. CLASSIFICATION ACCORDING TO THE ATEX
DIRECTIVE
The machine conforms to the essential requisites
of the EU Directive 94/9/EC, better known as
ATEX ("Explosive atmospheres"). It is classified as
group II category 3 letter G system. The assess-
ment procedures of conformity, carried out by an
internal factory check, allow the installation of
the machine in surroundings where there may be
potentially explosive atmospheres due to the
presence of gas, fumes or mist.
Preparation for extraction of gases
For the compliance ATEX, the machine is equi-
pped with a system of forced evacuation of the
fumes generated during the operation.
The smoke evacuation takes place through a
chimney on the upper end of the machine and is
powered by a forced suction (venture effect) that
is automatically activated depending on the
mode of operation of the machine.

7. INSTALATION

This chimney must then be connected to the gene-
ral workshop extraction or brought outside the
workshop.
In this second case, the chimney connected to the
machine must cover at least a portion in the verti-
cal of 1 meter before being led outside.
For an easy installation, the chimney is generally
an aluminum tube, flexible and extensible.
The fumes of solvent dispersed in that way do not
need further treatment.

7.5. POSITIONING

The S25 must be positioned in a well-aired place.
The area must be equipped with all means provi-
ded for by the Italian Legislative 626/94,
relating to Italian Legislation with reference to the
health and safety of the workers in the working
environment.
Position the machine on the floor and make sure
that there is sufficient space around the machine
to carry out normal maintenance operations or
inspections.

7.6. PUTTING INTO USE

1. Connect the grounding cable (nº9) provided
with the machine and marked yellow/green from
the side of the cable lug to the hole (nº6) at the
base of the machine, and connect the other side
of the grounding cable with free terminal to the
earth contact of the electrical supply.
2. Make sure that the on/off switch (nº18) of the
machine is in the off position.
3. Connect the quick coupling of the machine's
(nº7) air supply to the compressed air supply
(max. 10 bar).
4. Place a clean solvent drum under the machine.
Then insert the suction filter (nº1) and the drain
hose (nº2) inside the drum.
5. Dismantle the gun and empty the canister into
a suitable recipient. Raise the lid of the automatic
washing tank.
6. Press the trigger of the spray gun and use the
nylon clip (nº16) to block the trigger of the spray
gun.
- 14 -