Opening And Closing The Disc Holder And Loading A Disc - Denon DN-T645 Instrucciones De Operación

(2) PARALLEL (DN-T645 only)
NOTE : All input is active low.
Pin No. Signal Name
1 FG
14 CD PITCH ON / OFF
2 CD PLAY
15 DECK FF
3 CD PAUSE
16 DECK COUNTER MEMO
4 CD CUE
17 CD PITCH +
5 CD 9
18 DECK REC
6 CD 8
19 DECK REWIND
7
7 CD
• Use the connection example in the diagram below as reference for connecting a parallel remote controller
to the DN-T645.
DECK CD FADER START
CD CD
CD PITCH DECK DECK CD PITCH
2 Installation precautions
• If the DN-T645/625 is placed near an amplifier, tuner or other components, noise (induced hum) or beat
interference may result (especially during AM or FM reception).
If this occurs, separate the DN-T645/625 from other components or reorient its position.
I / O Pin No. Signal Name
_
20 CD PITCH –
I 8 CD 6
I 21 CD SYNC.
I 9 CD FADER START
I 22 DECK COUNTER RESET
I 10 Command common
I 23 Command common
I 11 DECK PLAY FORWARD
I 24 DECK STOP
I 12 DECK PLAY REVERSE
I 25 DECK PAUSE
I 13 CD STOP
I
CD CD CD CUE CD
DECK MEMO DECK CD PITCH ON/OFF CD
DECK DECK DECK RESET
The CD player uses a microcomputer for controlling
internal electronic circuits. In the event that the player
is used while a near-by tuner or TV is turned on,
I / O
although unlikely, interference could occur either in the
sound from the tuner or the picture of the TV. To avoid
I
this, please take the following precautions.
I
• Keep the CD player as far away from the tuner or TV
I set as possible.
• Keep the power cable and connecting cable of the
I
CD player separate from the antenna wires of the
I
tuner and TV.
_ • Interference is particular likely to occur when an
indoor antenna or a 300 Ω/ohms feeder cable is
_
used. Thus, use of an outdoor antenna and 75
Ω/ohms coaxial cable is strongly recommended.
I
I
NOTE :
I
• Use this unit in a horizontal orientation.
I
When the unit is used with the front panel facing upward (and the unit us in a vertical orientation) or when
I
the front panel is on an incline, the unit will not operate properly.
4 OPENING AND CLOSING THE DISC HOLDER AND
LOADING A DISC
Opening and closing the disc holder
✽. This operation only works while the power is on.
1. Press the power operation switch q to turn on the power.
2. Press the OPEN/CLOSE button w.
CD
How to load a disc
• Make sure the disc holder is completely open.
DECK
• Hold the disc by the edges and place it on the disc
tray. (Do not touch the signal surface, i.e., the
glossy side.)
• When using 12 cm. diameter discs, make sure the
outer edge matches the tray guide circumference
and when using CD signals (8 cm. diameter) match
CD SYNC.
the outer edge with the inner tray guide
circumference.
• Press the OPEN/CLOSE button w to close the disc
holder #2 .
• When the disc holder is open and a disc is loaded,
you may also press the play/pause (
to close the disc holder. (If the play/pause (
button is pressed, playback will start immediately
upon the disc contents having been read.)
Messages
Message
No Disc No disc inserted, disc unreadable or disc inserted upside down.
TOC Error The disc information has not been read properly.
Invalid CD The disc is a CD-ROM that does not contain MP3 files.
Tray Error The disc holder could not be opened or closed properly.
300 Ω/ohms feeder cable
CAUTIONS :
• If you finger should get caught in the disc
holder when it closes, press the OPEN/CLOSE
button.
• Do not place any foreign objects on the disc
tray, and do not place more than one disc on the
tray at a time. Otherwise malfunction may
occur.
• Do not push in the disc tray manually when the
power is off as this may cause malfunction and
damage the CD player.
• This player can play CD-R/RW discs, but only if
) button t
1 3
they are finalized. Note however that depending
1 3
)
on the recording quality, the player may not be
able to play some finalized CD-R/RW discs.
Meaning
ENGLISH
75 Ω/ohms coaxial cable
9