Tabla de contenido
Publicidad
the path of the fall.
• to use an AS anchor ring if you are not in top physical
conditon.
• to use an AS anchor ring if you are a pregnant
woman.
• to use an AS anchor ring if the safety function of one
of the related items is affected by the safety function
of another article or interferes therewith.
• to use an AS anchor ring to secure a load of
equipment.
• to moor an AS anchor ring to a host structure whose
resistance is less than 13 kN or considered to be
such.
• to use an AS anchor ring as a way of slinging.
• to install an AS19 S anchor ring using type 1 mooring
to the connector (Fig. 3.a).
• to carry out any repair operation on an AS anchor
ring.
• to install an AS anchor ring using type 2 mooring
to the connector if the angle formed by the loops is
greater than 90°.
8. Installation
8. Installation
Verifi cation before use:
• The AS anchor ring has been subject to periodic
inspection (Section 14).
• The length of the AS anchor ring is compatible with
the size of the intended host structure.
• The breaking strength of the host structure is
greater than or equal to 13 kN or considered as such
(Figure 3).
• The AS Anchor ring is compatible with the sharpness
of the edges of the envisaged host structure.
The AS anchor ring can be used to moor a retractable
fall-arrest or energy absorber or mobile fall-arrester
on rigid anchor or a mobile fall-arrester on a fl exible
anchor.
IMPORTANT
Before and during use, it is necessary to plan
out how possible rescue can be effi ciently and
safely conducted, within less than 15 minutes.
Beyond 15 minutes, the fallen operator is in
danger of dying.
9. Material
9. Material
Strap: polyester
Stitching thread: polyester
10. Associated equipment
10. Associated equipment
Fall-arrester system (EN 363).
An anchorage (EN 795).
An end connector (EN 362).
A fall-arrest (EN 353-1/2 – EN 355 – EN 360).
A connector (EN 362).
A descender (EN 361).
Before using a EN 363 fall-arrester system, the user
must ensure that each of the components is in good
working order.
11. Maintenance and storage
11. Maintenance and storage
If an AS anchor ring is dirty, wash it with clean cold
water and possibly with a detergent for delicate
fabrics, using a synthetic brush.
If during use or washing the AS anchor ring is soaked,
leave it to dry naturally in the shade and away from
any heat source.
See fi g. 2.
During transport and storage, protect the equipment in
a moisture-free package against any danger (source
of direct heat, chemical products, UV radiation, etc.).
12. Equipment compliance
12. Equipment compliance
TRACTEL SAS RD 619 – Saint-Hilaire-sous-Romilly
– F-10102 Romilly-sur-Seine France hereby declares
that the safety equipment described in this manual,
• complies with the requirements of European
Directive 89/686/EEC of December 1989,
• is identical to the PPE covered by the CE
type examination certifi cate issued by APAVE
SUDEUROPE SAS - BP 193 - 13322 Marseille -
France identifi ed by number 0082, and tested in
accordance with standard EN 795 dated 2012,
• is subject to the procedure referred to in Art. 11B of
Directive 89/686/EEC, under the control of a notifi ed
body: APAVE SUDEUROPE SAS – CS 60193
– 13322 Marseille – France, identifi ed under the
number 0082.
13. Marking
13. Marking
The label on each AS anchor ring indicates:
a. The trade name: TRACTEL
b. The name of the product, eg: AS19 S 0.6 (AS19 S
anchor ring length 0.6 m),
c. The reference standard followed by the year of
application,
,
®
7
GB
Publicidad
Tabla de contenido
