Description; Composition Of A Standard Supply; Technical Specifications; Associated Equipment - Tractel rollclamp Manual De Instalación, Empleo Y Mantenimiento

"IMPORTANT": Placed at the beginning of a
line, designates instructions given to prevent a failure or
damage to equipment, but not directly endangering the
life or health of the operator, or other persons, and/or
not likely to cause damage to the environment.
GB
"NOTE": Placed at the beginning of a line,
desi gnates instructions given to ensure efficient and/or
com fortable use of an installation, a utilisation method
or a mainte nance operation.
You must read the user manual.
Enter information on inspection sheet.
Enter the information on the detachable inspection
sheet given on the central page of this manual.
OK
CORRECT USE:
Correct use of the equipment.
The rollclamp fall-arrest safety system is a portable
mansafe fall-arrest anchor point. The system is fast and
easy to set up. One of the main advantages of this
equipment is that it can be secured at either the upper
or lower part of the anchoring beam. It can be installed
on a wide range of anchoring beams of varying lengths
and heights.
The rollclamp anchor point is certified per standard
EN 795-B: 1996 + A1: 2000
provisional anchor point for 1 person.
4. Composition of a standard unit
The rollclamp anchor system standard supply com -
prises:
• 4 guide rings (fig. 1, item 1).
• 2 or 4 guide shoes, depending on model, size M or
L (fig. 1, item 2).
• 1 mobile jaw (fig. 1, item 3).
• 1 indexing knob (fig. 1, item 4).
• 1 locking pin (fig. 1, item 5).
• 1 fixed jaw (fig. 1, item 6).
• 1 guide rod (fig. 1, item 7).
• 1 securing strap (fig. 1, item 8).
• An anchor point nameplate (fig. 1, item 12).
• A plastic bag containing this installation, utilisation
and maintenance manual.

5. Technical specifications

16

3. Description

as a transportable
The dimensions given in the table below are referenced
on fig. 3.
M(*)
P (kg) 1,5
L1 (mm) 580
L2 (mm) 152
L3 (mm) 475
L4 (mm) 42
D1 (mm) 25
D2 (mm) 32
D3 (mm) 42
P: Weight of unit.
(*) M: Model M rollclamp anchor point.
L: Model L rollclamp anchor point.
Materials used in components:
• Guide rings and shoes (fig. 1, item 1/2): Plastic
• Mobile and fixed jaws (fig. 1, item 3/6): Cast
aluminium.
• Indexing knob (fig. 1, item 4): Aluminium and
stainless steel.
• Guide rod (fig. 1, item 7): Aluminium.
• Locking pin (fig. 1, item 5): Stainless steel.
• Securing strap (fig. 1, item 8): PE.

6. Associated equipment

To ensure its safety function, the rollclamp anchor
system must be used in association with a fall-arrest
personal protective equipment (PPE) connected to the
anchor point. The PPE equipment associated to the
anchor point must be CE certi fied, manufactured in
compliance with Directive 89/686/CEE, and used in
compliance with Directive 89/656/CEE. Tractel
distributes a range of PPE satisfying the requirements
of the se directives and compatible with the rollclamp
anchor system.
DANGER: The rollclamp anchor system can
only be used with a single fall-arrest PPE under the
terms of Directive 89/686/CEE.

7. Preliminary study

To ensure correct operation of the rollclamp anchor
system, and therefore of the overall fall-arrest safety
system, the following requirements must be satisfied on
the anchor point installation structures and surfaces.
The steel anchoring beam (I or H) on which the
rollclamp anchor point is installed must be able to
handle a load of 10 kN along the entire travel distance
planned for the anchor point (fig. 4).
DANGER: If several rollclamp anchor points are
L(*)
2
1000
208
GB
685
98
25
32
42
®