Atlas Copco Dynapac SD1800C Manejo Y Mantenimiento página 216

KWP SPN FMI
846 523452 2
849 1176 3
850 1176 4
856 523613 0
857 523613 0
858 523613 0
859 523613 0
860 523613 0
861 523613 1
862 523613 0
864 523613 2
876 523470 7
877 157 3
878 157 4
881 523633 11
882 523633 11
883 523633 11
887 3234 11
889 3224 1
892 4345 11
893 4343 11
894 4374 13
D 23.18 60
Code Error Identification
1-4-3 Multiple Stage Switch engine torque limi-
tation curve; plausibility error
6-8-0 Sensor error pressure sensor upstream
turbine; signal range check high
6-8-0 Sensor error pressure sensor down-
stream turbine; signal range check high
1-3-4 Rail pressure disrupted
1-3-4 Rail pressure disrupted
1-3-4 Rail pressure disrupted
1-3-4 Rail pressure disrupted
1-3-4 Rail pressure disrupted
1-3-4 Minimum rail pressure exceeded
(RailMeUn3)
1-3-4 Rail pressure disrupted
1-3-4 Setpoint of metering unit in overrun
mode not plausible
1-4-6 Maximum rail pressure in limp home
mode exceeded (PRV)
1-4-7 Sesnor error rail pressure; signal range
check high
1-4-7 Sensor error rail pressure; signal range
check low
7-0-1 Nox conversion rate insufficient
7-0-1 Nox conversion rate insufficient
7-0-1 Nox conversion rate insufficient
8-0-7 Nox Sensor downstream of SCR Cataly-
sator; plausibility error "stuk in range"
8-0-8 Nox sensor upstream of SCR Catalysa-
tor; low signal not plausible
8-7-0 Sensor backflow line pressure (SCR);
plausibility error
8-7-1 General pressure check error (SCR)
8-7-2 Pressure stabilisation error dosing valve
(SCR)
Short Text Detail
Multiple Stage Switch engine torque limitation
curve; plausibility error
Sensor error pressure sensor upstream tur-
bine; signal range check high
Sensor error pressure sensor downstream tur-
bine; signal range check high
Maximum positive deviation of rail pressure
exceeded (RailMeUn0)
Maximum positive deviation of rail pressure in
metering unit exceeded (RailMeUn1)
Railsystem leakage detected (RailMeUn10)
Maximum negative deviation of rail pressure in
metering unit exceeded (RailMeUn2)
Negative deviation of rail pressure second
stage (RailMeUn22)
Minimum rail pressure exceeded (RailMeUn3)
Maximum rail pressure exceeded (RailMeUn4)
Setpoint of metering unit in overrun mode not
plausible
Maximum rail pressure in limp home mode
exceeded (PRV)
Sesnor error rail pressure; signal range check
high
Sensor error rail pressure; signal range check
low
Nox conversion rate insufficient (SCR-Cat
defect, bad AdBule quality)
Nox conversion rate insufficient (SCR-Cat
defect, bad AdBule quality); temperature range
1
Nox conversion rate insufficient (SCR-Cat
defect, bad AdBule quality); temperature range
2
Nox Sensor downstream of SCR Catalysator;
plausibility error "stuk in range"
Nox sensor upstream of SCR Catalysator; low
signal not plausible
Sensor backflow line pressure (SCR); plausibil-
ity error
General pressure check error (SCR)
Pressure stabilisation error dosing valve (SCR)