Peltor WS Serie Manual Del Usuario página 11

► Turn the Bluetooth button slowly clockwise to increase the volume.
®
► Turn the Bluetooth button slowly anti-clockwise to decrease the volume. The volume is adjustable in eight steps.
®
The last setting is stored when the headset is switched off.
Turn the Bluetooth button anti-clockwise as far as it will go (lowest volume) to activate the FM radio or surround
®
sound.
► Turn the Bluetooth button slowly clockwise to reactivate the stereo music.
®
4. Answering incoming calls on a connected phone
The ringer is controlled from the phone. If the phone transmits its own ring signal, you hear this; otherwise you hear the
headset's signal, four different tones.
► Press the Bluetooth
®
► Press and hold the Bluetooth
noise compensation, place the headset microphone no more than a few millimetres from the corner of your mouth!
5. Voice-controlled dialling from the headset via a connected phone
This is a telephone function and is specific to the telephone model.
► Press the Bluetooth
®
Some telephones do not send a signal when it is time to say the voice dial command.
6. Redialling with a connected phone
This function is only available with mobile phones that use a Bluetooth
► Press and hold the Bluetooth
7. Transferring calls to/from a phone
This function is only available with mobile phones that use a Bluetooth
► Press and hold the Bluetooth
back to the WS Alert, press the Bluetooth
8. Setting the call volume level
You have four volume levels.
► Turn the Bluetooth button slowly clockwise to increase the volume.
®
► Turn the Bluetooth button slowly anti-clockwise to decrease the volume.
®
A tone is emitted when the volume reaches the maximum or minimum level.
You can only adjust the volume during a call. The last selected setting is stored when the unit is switched off.
Note: Adjust the volume while working in a noisy environment, as all warning signals are also controlled by the volume
setting!
9. Disconnecting a call via a connected phone
► Press the Bluetooth
®
This is confirmed with two descending tones.
10. Low-battery warning
When the battery has enough power left for about 5 minutes of usage time, the headset emits three brief tones every
30 seconds to indicate that the battery needs replacing. The LED glows red and the headset switches off automatically
when the battery dies.
11. Range indication
If you have already done the initial pairing, the headset automatically searches for the linked Bluetooth
phone the next time you turn it on. Once it has established a Bluetooth
establish a link, you hear two descending tones. (The unit does not automatically try to reconnect.)
If the connected unit is out of range so that the Bluetooth
minutes. After that, it conserves energy by only attempting to reconnect every 15 minutes, until the link is re-established
or until the headset automatically switches off (see above). If the link is re-established, you hear two ascending tones; if
no connection is found, the headset remains ready to re-establish the Bluetooth
However, if a connection with a mobile phone is broken while the Bluetooth
automatically. The warning signal (two descending tones) stops automatically when the headset is in range again.
► Press the Bluetooth
®
► Press briefly on any of the headset's buttons to restart the warning signal.
12. Other indicators
GSM connection broken
If the phone loses its connection with the network, you hear a warning in the headset every 10 seconds.
Hands-Free Profile
button briefly to connect the phone call to the headset. A tone confirms connection.
button for more than two seconds to refuse the call. Note: For maximum ambient-
®
button briefly and say your voice dial command.
button for more than 2 seconds to redial the last-dialled number via your WS Alert.
®
button for more than two seconds to transfer the call to the phone. To move the call
®
button briefly.
®
button briefly to disconnect a call.
button briefly to switch off the warning signal.
Handsfree Profile.
®
Handsfree Profile.
®
link, you hear two ascending tones. If it cannot
®
link is broken, the headset searches for the paired unit for 3
®
®
link is established, it is not reconnected
®
5
®
link with the paired unit.
adapter or