Peltor WS Serie Manual Del Usuario página 8

EN
PELTOR WS ALERT – ACTIVE-VOLUME HEARING PROTECTOR RADIO
The Peltor WS ALERT active-volume hearing protector radio, M2RX7*WS4, provides comfortable, effective protection
from harmful noise. The active-volume function enhances safety by attenuating loud noises and amplifying weak ones.
In addition, the WS ALERT has an FM radio receiver and Bluetooth
profiles.
Read these instructions carefully to ensure the best possible benefit from your Peltor WS ALERT.
(A) WHAT IS WHAT?
1. Extra broad headband (M2RX7A) with soft padding for ideal comfort throughout the working day. Specially designed
helmet attachments (M2RX7P3E) with slots for attaching a visor and rain shield.
2. Individually sprung headband wires of stainless steel provide an even distribution of pressure around the ears.
Maintains its resilience better than regular plastic headbands through a wide range of temperatures.
3. Low, two-point fasteners and easy height adjustment with no protruding parts.
4. Soft, wide foam/fluid-filled ear cushions with built-in pressure-relief channels for low pressure, effective sealing and
individual comfort.
5. Short, flexible antenna for stereo reception, with a low attachment point and high receptivity.
6. Battery cover for easy battery replacement.
7. Microphones for active volume capture and amplifying weak sounds up to the specified maximum level.
8. On/off and volume controls.
9. Channel search control. Switches automatically from stereo to mono for the best reception in the event of a weak
signal.
10. Active volume controls. On/Off and volume.
11. Speech microphone allows two-way communication by Bluetooth
12. Bluetooth controls.
®
13. LED for Bluetooth .
®
BATTERIES
Unscrew and open the battery cover. Insert the two enclosed 1.5-volt AA batteries. Make sure that the + and – poles
are in the correct position. You can also use rechargeable AA batteries.
RADIO FUNCTION
On/off, volume and channel settings
To switch the radio amplification on and off and adjust its volume, turn the volume control knob (8). Use the channel
selector knob (9) to select a channel.
SURROUND
To switch the ambient sound amplification on and off and adjust its volume, turn the volume control knob (10).
BLUETOOTH
Turn or press the Bluetooth
instructions, see the user guide for the Bluetooth
surround sound or radio.
(B) INSTALLING A HEADBAND/HELMET ATTACHMENT
Headband:
(B:1) Slide out the shells. Place them over your ears so that the ear cushions fit snugly.
(B:2) Adjust the height of the shells to a snug, comfortable fit by pulling the shell up or down while holding the headband
down.
(B:3) The headband should lie across the top of the head.
Helmet attachment:
Insert the helmet attachment in the slot on the helmet and snap it into place (see fig. B:4). To switch the unit from
ventilation to working mode, press the headband wires inwards until you hear a click on both sides. Ensure that the
shell and the headband wires in working mode do not press on the edge of the helmet so that noise leakage can
occur.
Note: The shells can be set in two positions: (B:5) working mode and (B:6) ventilation mode.
Important! For the best protection, brush aside hair around the ears so the ear cushions fit snugly against the head.
Spectacle frames should be as thin as possible and fit close to the head.
IMPORTANT USER INFORMATION
• The hearing protector radio must be put on, adjusted, cleaned and maintained in accordance with the instructions in
this manual.
• Wear the hearing protector radio 100% of the time you spend in noisy environments for full protection.
• Clean the outside of the unit regularly with soap and warm water. Do not immerse in water.
• Do not store the unit in temperatures exceeding +55 °C, for example on a dashboard or windowsill.
• Certain chemical substances may be harmful to this product. Contact the manufacturer for more information.
• When interference increases or the volume becomes too weak, it is time to replace the batteries. Never replace
controls (12) to switch the unit on or off, adjust volume and pair with other units. For
®
function (F). The Bluetooth
®
that supports headset, handsfree and A2DP
®
or connection to a com radio etc.
®
link cannot be active while using the
®
2