Setting The Subwoofer Channel (Subw. Channel); Equalizer Presets (Factory's Eq); Setting The Response Slope For The High Range Speaker (Tw Setup); Setting The Filter Type - Alpine CDA-9886 Manual De Operación

Setting the Subwoofer Channel
(SUBW. Channel)
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
STEREO (Initial setting)
STEREO: Subwoofer stereo (L/R) output
MONO: Subwoofer monaural output

Equalizer Presets (Factory's EQ)

10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Flat Pops Rock
Electrical Dance Hip Hop&Rap
Country Classical User1
User4 User5 User6
• By selecting User's 1 to 6, you can recall the stored preset number in
"Adjusting the Graphic Equalizer Curve" (page 32) or "Adjusting
the Parametric Equalizer Curve" (page 32) .
Setting the Response Slope for the High
Range Speaker (TW Setup)
Depending on the response characteristics of the speaker, care should be
taken when setting the response slope of the high range speaker to
FLAT in 2.2ch (3WAY) mode (see "Adjusting the Crossover Settings"
on page 32), as speaker damage may result.
MAKER'S (Initial setting )
MAKER'S: As protection from possible speaker damage, FLAT
cannot be set for the response slope of the high
range speaker in 2.2ch (3WAY) mode.
USER'S: The FLAT setting is possible in 2.2ch (3WAY) mode.

Setting the Filter type

NORMAL (Initial setting)
NORMAL (L=R): Left and right speakers are adjusted
equally.
INDIVIDUAL (L/R): Left and right speakers are individually
adjusted.

Turning Media Xpander ON/OFF

When the Media Xpander is on, you can adjust the Media Xpander level
(refer to page 31).
OFF (Initial setting) ON

Setting the MX Level

MX (Media Xpander) makes vocals or instruments sound distinct
regardless of the music source. The FM radio, CD, USB memory and
iPod, will be able to reproduce the music clearly even in cars with a lot
of road noise.
Changing the source to which you want to apply Media
Xpander.
FM (MX level 1 to 3):
The medium to high frequencies become clearer, and produces
well balanced sound at all frequencies.
MONO
News Jazz&Blues
Easy Listening
User2 User3
USER'S
INDIVIDUAL
CD (MX level 1 to 3):
CD mode processes a large amount of data during playback.
MX takes advantage of this large data quantity to reproduce a
more clear, clean output.
CMPM/SAT (MX level 1 to 3):
This corrects information that was lost at the time of
compression. This reproduces a well-balanced sound close to
the original.
DVD (Video CD)
(MOVIE MX level 1 to 2):
The dialogue portion of a video is reproduced more clearly.
(DVD MUSIC):
A DVD or Video CD contains a large quantity of data such as
music clip. MX uses this data to reproduce the sound
accurately.
AUX (MX level 1):
Choose the MX mode (CMPM, MOVIE, or MUSIC) that
corresponds to the media connected.
• Each music source, such as FM radio, CD, and MP3/WMA/AAC can
have its own MX setting.
• On disks with both MP3/WMA/AAC and CD-DA, when the source
changes from "MP3/WMA/AAC to CD-DA" or "CD-DA to
MP3/WMA/AAC", MX-mode switching may delay playback slightly.
• Setting to Non Effect sets MX mode of each music source to OFF.
• The function is inoperable when DEFEAT is set to ON.
• There is no MX mode for AM radio.
• If an audio processor with the MX function (PXA-H701, etc.) is
connected, its own MX processing is applied to the music source.
Since the processor MX settings may not match the head unit, the
audio processor needs to be adjusted. For details, refer to the
Owner's Manual of the audio processor.
• "CMPM" is applied for MP3/WMA/AAC and iPod.
• "SAT" is applied for XM radio and SIRIUS radio.

Setting EQ mode

This setting gives you a choice of 5-band parametric, or 7-band graphic
equalizer.
Parametric EQ (Initial setting)
PEQ: 5-band Parametric EQ
GEQ: 7-band Graphic EQ
Setting the Time Correction Unit (TCR
Parameter)
You can change the unit, (cm or inch) of time correction.
TCR Parameter<cm> (Initial setting)

Blackout Mode On and Off

When Blackout mode is turned on, all display indications on this unit
will turn off to reduce power consumption. This additional power
enhances the sound quality.
OFF (Initial setting) ON
• When Blackout mode is set to ON, in 5 seconds after returning to
normal mode, all displays on the unit will turn off.
• If any button on the unit is pressed during the blackout mode, the
function will be displayed for 5 seconds to show the operation before
returning to Blackout mode.
Graphic EQ
TCR Parameter<inch>
31
-EN