Sawing According To Tracings; Sawing With The Parallel Stop; Working With The Roller Edge Guide; Setting For Mitre Cuts - Mafell KSS60 18M bl Traducción Del Manual De Instrucciones Origina

blade enters the workpiece. As soon as the slit
behind the saw blade is cleared during the
forward motion of the machine, the riving knife
reverts to its normal position.
In case of repetitive plunge cuts of
the same depth, the plunging depth
can be preset.
Proceed as follows:

Set the machine to the desired cutting depth.

Open the clamping screw 17 (Fig. 2) and set the
stop bar 18 (Fig. 2) downwards up to the limit
stop.

Retighten the clamping screw. After completion
of the plunge work, set the stop bar into the top
position.

5.7 Sawing according to tracings

with guide rail
When sawing according to tracing, the right edge of
the guide rail serves as tracing indicator. This also
applies to bevel cuts. Please take note of Section 5.5.

For sawing, place the guide rail onto the
workpiece.

Switch on the machine (see Chapter 5.2) and
slide the machine evenly in cutting direction.

When the cut is completed, switch off the saw
by releasing the switch trigger 10 (Fig. 2).

Pull back the machine into home position
keeping it applied to the workpiece and take it
off the workpiece
With doing so, you guarantee that the
retractable saw guard is completely closed.
without guide rail
You can detach the machine from the guide rail
towards the rear by pressing the ratchet 24 (Fig. 6).
The retractable marking indicator 19 (Fig. 3) is
automatically adjusted for bevel cuts as well. The
tracing edge corresponds to the saw blade's inside.
For diagonal cuts, the marking can be viewed through
the opening on the left-hand side of the upper saw
guard (arrow, fig. 1).
in this position.
-28-

Hold the machine by its handles and place the
front part of its base plate onto the workpiece.

Switch on the portable circular saw (see chapter
5.2) and slide the machine evenly forward in the
direction of the cut.

When the cut is completed, switch off the saw
by releasing the switch trigger 10 (Fig. 2).

5.8 Sawing with the parallel stop

The parallel stop serves to saw parallel to an already
existing edge. The limit stop can be attached to the
left or right of the machine. While doing so, the cutting
range amounts to 33 - 130 mm on the right-hand side
(reading indicator "X" Fig. 1) and to 163 - 300 mm on
the left-hand side (reading edge at indicator edge "Y"
Fig. 1).

You can adjust the cutting width after releasing
the wing screws 20 (Fig. 3) by moving the limit
stop accordingly and afterwards retightening the
wing screws.
In addition, by simply turning it around (guide face for
the workpiece edge points upwards), the parallel stop
can also be used as double support to improve
guidance of the portable circular saw. Now the
machine can be guided along a guide that is fastened
on the workpiece.

5.9 Working with the roller edge guide

The roller edge guide serves to work parallel to an
already existing edge. The limit stop can be attached
to the left or right of the machine. The cutting range
on the right-hand side amounts to approx. 12 - 40 mm
(0.47 - 1.57 in.) and on the left-hand side to approx.
30 – 210 mm (1.18 - 8.27 in.).

You can adjust the cutting width after releasing
the wing screws 20 (Fig. 3) by moving the limit
stop accordingly and afterwards retightening the
wing screws.

5.10 Setting for mitre cuts


Release the limit stop 25 (Fig. 6) and adjust the
angle according to the scale on the guide rail.

Afterwards retighten the limit stop.

Place the machine with the two stop bolts at the
bottom side of the guide rail against the