Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
PowPak
| Programming
TM
Dimming Module with EcoSystem
®
Part of the Energi TriPak
Part of the Energi TriPak
Family
Family
TM
TM
ALL PROGRAMMING IS OPTIONAL
Programming is not required for default functionality
•
Device grouping
• Set a favorite light level
•
Set high-end trim for all fixtures
•
Set occupancy levels
•
Set minimum light level for all fixtures
•
Multiple-row daylighting
Please consult individual component installation and programming
guides for more details.
Set a favorite light level
7
(Optional)
For Pico
Wireless Transmitters with a Preset Button
®
Adjust lights to desired level:
A
Use "Raise/Lower" on Pico
Wireless Transmitter.
®
B
Save favorite level:
Press and hold "Preset" for 6 seconds.
Set high-end trim for all fixtures
8
Setting High-End Trim:
Lighting electricity usage can be reduced
by 20% or more through high-end trim,
which sets the maximum light level for
each space.
For example, the human eye can barely
distinguish between a 100% and an
80% light level—setting lights to 80%
reduces energy use by about 20%.
For best results, minimize the amount of sunlight entering the room
before performing the following procedure.
A
Enter trim adjustment mode:
Press & hold Raise "
" for 12 seconds.
Ballasts will flash high-low-high and top LED will be lit solid.
B
Adjust the high-end trim:
Use Raise "
" and Lower "
" to adjust and set
the lights to the desired high-end. (50 to 100%)
C
Save the high-end trim:
Press & hold All On "
" for 6 seconds to save setting.
Top LED will turn off to indicate new level has been saved.
10
Set minimum light level for all fixtures
(Optional)
Certain applications, such as hallways, may require that the lights
never turn off. For these areas, select the 10% option.
A
Enter minimum light level adjustment mode:
Press & hold Lower "
" for 12 seconds.
Ballasts will flash high-low-high and bottom LED will be lit solid.
B
Adjust the minimum light level:
Press Raise "
" to set low-end trim to 10%.
Press Lower "
" to set low-end trim to off.
C
Save the minimum light level:
Press & hold All On "
" for 6 seconds.
Bottom LED will turn off to indicate new level has been saved.
6
Device grouping
(Optional)
Device grouping
041-361
Rev. A
allows Pico
Wireless
10/2011
®
Transmitters and
Radio Powr Savr
TM
Daylight Sensors to
Daylight
Sensor
control a group of
lights instead of all
lights in the room.
Default:
All Wireless
Transmitters
control all
light fixtures.
Enter Grouping
A
Press and hold All On
"
" & Raise
"
" for 6
seconds until the
Clear Connect
and
TM
EcoSystem
LEDs
®
begin flashing at a
rate of
⁄
second ON
1
2
⁄
second OFF.
1
2
Link
Note: Occupancy Sensors cannot be grouped
and will control all fixtures.
Set occupancy light levels
9
(Optional)
Note: Unoccupied light level is always the minimum light level and cannot be adjusted.
A
Set desired occupancy light levels:
Use raise / lower
on PowPak
"
/
"
Note: If certain lights should be unaffected by occupancy, turn lights off using Pico
B
Save occupancy light levels:
Press and hold " Test " for 6 seconds on any associated Radio Powr Savr
without a "Lights On" button. Release when Sensor lens starts to flash. Or, press and hold
" Lights On " for 6 seconds on any associated Radio Powr Savr
Release when Sensor lens starts to flash.
11
Multiple-row daylighting
Radio Powr Savr
TM
Sensor must be grouped (Step 6)
Group sensor with ballasts before
beginning multiple-row daylighting.
Cal.
Link
Test
PowPak
Pico
TM
Dimming Module
Wireless
Transmitter
Raise
All On
Lower
Need Help? www.lutron.com or call the Lutron Technical Support Center, 24/7 at 1.800.523.9466
Private office
Windows
or small room
Grouping NOT required.
In small rooms such as
private offices, all lights
Link
Test
should respond together
and grouping is
PowPak
TM
Dimming
not required.
Module
For more information:
www.lutron.com/powpakdimming
Pico
®
Wireless
Transmitter
Start Grouping
Assign Fixtures
B
C
Assign / Unassign
Hold
"Lights Off"
6 Seconds
Hold
"Link"
6 Seconds
Link
Cal.
Link
Cal.
Cal.
Test
Test
Test
First ballast will flash.
Assigned: Bright
Unassigned: Dim
(Optional)
Dimming Module or raise / lower on Pico
, Transmitter(s)
TM
®
Transmitter(s).
®
Occupancy Sensor
TM
Occupancy Sensor.
TM
A
Press and hold All On "
(Optional)
Dimming Module for 6 seconds. Fixtures not controlled by the
Daylight Sensor will go to OFF, all others will go to low end.
Daylight Sensor
(First ballast will begin to flash.)
B
Press Raise "
" on PowPak
of any associated Pico
Transmitter to toggle the fixture from
®
Window Row (low-end) to Inside Row (high-end), or vice versa.
C
Press Lower "
" on PowPak
on any associated Pico
®
(Next fixture will flash.)
D
Repeat steps B and C until all rows have been properly set up.
®
Press and hold All On "
E
"Preset" on any associated Pico
(Window Row will begin to flash.)
Lights
F
Using the Raise/Lower "
On
Module or an associated Pico
desired light level.
Raise
G
Tap All On "
" on the PowPak
Preset
" Lights Off " on any associated Pico
Lower
H
Repeat steps F and G until both rows are properly set up.
Lights
I
Press and hold " Cal. " on the daylight sensor to calibrate room.
Off
See step 5 of "Daylight calibration" on reverse.
Windows
WINDOW ROW
PowPak
Dimming
Module
INSIDE ROW
Transmitters
Repeat until all fixtures have
been assigned / unassigned
Next Fixture
Tap
Tap
"Lights On"
" Lights
Off"
Tap "Cal."
Tap "Link"
Link
Cal.
Test
This will save current group.
Selected ballast will flash.
Repeat B-D for other
Wireless Transmitters.
FCC Information:
This device complies with part 15 of the FCC Rules and Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference, and
.
(2) this device must accept any interference, including interference that
may cause undesired operation.
Modifications not expressly approved by Lutron Electronics Co., Inc. could
void the user's authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged
" and Lower "
" on the PowPak
TM
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Dimming Module, or "Lights On"
TM
Limited Warranty
(Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in
Dimming Module, or " Lights Off "
TM
materials or manufacture within one year after purchase. For warranty
Transmitter to move to the next fixture.
service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd.,
Coopersburg, PA 18036-1299, postage pre-paid.
This warranty is in lieu of all other express warranties, and the implied war-
ranty of merchantability is limited to one year from purchase. This warranty
does not cover the cost of installation, removal or reinstallation, or damage
" on PowPak
Dimming Module, or
resulting from misuse, abuse, or damage from improper wiring or installation.
TM
Transmitter for 6 seconds.
This warranty does not cover incidental or consequential damages.
®
LUTRON'S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING
OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE,
/
" buttons on the PowPak
Dimming
INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER
TM
Transmitter set the current row to your
EXCEED THE PURCHASE PRICE OF THE UNIT.
®
This warranty gives you specific legal rights, and you may have other rights
which vary from state to state. Some states do not allow the exclusion or
Dimming Module or
TM
limitation of incidental or consequential damages, or limitation on how long
to move to the next row.
an implied warranty may last, so the above limitations may not apply to you.
®
Lutron, Pico, EcoSystem, Hi-lume, and
PowPak, Radio Powr Savr, Energi TriPak and Clear Connect are trademarks
of Lutron Electronics Co. Inc. ©2011 Lutron Electronics Co., Inc.
Large office or
classroom
Radio
Powr Savr
TM
Grouping RECOMMENDED.
Occupancy
Sensor
In large rooms such as conference
rooms or classrooms, separate
control of some fixtures, such as
whiteboard lights or daylighting
TM
Link
Test
Daylight
rows, is beneficial. Grouping
Sensor
is recommended.
For more information:
www.lutron.com/powpakdimming
Pico
®
Wireless
Save Grouping
Exit Grouping
D
E
Press and hold
All On "
" &
Hold
Raise
"
"
"Lights Off"
for 6 seconds.
6 Seconds
Hold
"Link"
6 Seconds
Link
Cal.
Test
are registered trademarks and
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg PA, 18036-1299, U.S.A.
Publicidad
Tabla de contenido
