JVC DT-V24G1 Manual De Instrucciones página 16

Menu Configuration—MAIN MENU
For the operation procedure, see page 7.
Adjustment bar
Displayed when selecting
Operation guide
"BALANCE."
Shows the buttons for each
operation.
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
NOTE
Settings of "E.AUDIO GROUP"
The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.
(G means GROUP)
1G: channel(s) 1/2/3/4/1+2/3+4/1 – 4 (1G)
2G: channel(s) 5/6/7/8/5+6/7+8/5 – 8 (2G)
1-2G: channel(s) 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)
3G: channel(s) 9/10/11/12/9+10/11+12/9 – 12 (3G)
1-3G: channel(s) 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/1 – 4 (1G)/5 – 8 (2G)/
9 – 12 (3G)/1 – 8 (1G+2G)/1 – 12 (1-3G)
Example of the level meter display —Level meter position and audio channels
Ex.: When "LEVEL METER ch" is set to "LINE" and "BAR TYPE" is set to "3COLORS"
• The level meter with no audio signal input is displayed in white for "3COLORS", and in gray for "W.100."
• You can select the position of the level meter display—top or bottom of the screen (☞ "POSITION" in
"INFORMATION" on page 18).
• When "PEAK HOLD" is set to "ON," the maximum level meter value will remain displayed for a set period of
time. (At the time the signal input level reaches the highest value.)
OVER LEVEL REFERENCE LEVEL
Red
Yellow
Green
(cont.)
AUDIO SETTING
Settings for the audio output balance, EMBEDDED AUDIO signals and level meter
Item
BALANCE
AUDIO1 ASSIGN.
AUDIO2 ASSIGN.
E.AUDIO GROUP* 1
LEVEL METER
SETTING*
1
LEVEL METER ch
BAR TYPE
REFERENCE
LEVEL
OVER LEVEL
BAR
BRIGHTNESS
PEAK HOLD
* 1 Memorized for each input.
To do
Adjust the balance between the right and left speakers.
Select the video input which the audio signal through
AUDIO ASSIGN (IN 1) terminal is assigned to.
Select the video input which the audio signal through
AUDIO ASSIGN (IN 2) terminal is assigned to.
Select the audio channel group of the EMBEDDED AUDIO
signals.
Adjust the level meter display for the EMBEDDED AUDIO
signals.
Select how the audio channels are displayed on the level
meter.
Select the color of the level meter display.
Select the standard input level indicated on the level meter.
Select the input level's lower limit indicated in red for the
"3COLORS" display.
Select the brightness of the level meter.
Activates/deactivates the peak hold function of the level
meter.
14
Setting value
L5 – L1, 0, R1 – R5
SDI-1, SDI-2, DVI, COMP/
RGB, VIDEO-1, VIDEO-2
☞ "NOTE"
☞ "NOTE"
OFF, LINE (Displays
the channels 1 – 6 at
the left of the screen
and 7 – 12 at the right.),
DIVIDE (Displays the odd
channels at the left of
the screen and the even
channels at the right.)
3COLORS (3 colors to
indicate variations in input
levels), W.100 (white)
–20dB, –18dB
–10dB, –8dB, –6dB,
–4dB, –2dB
LOW, HIGH
OFF, ON