Ating Data; O Perating Conditions; Achine - SUHNER ABRASIVE ROTOmax 2.0 Documentación Técnica

2.2.4 s
Afety guArd
If a safety guard is supplied with the hand tool, it is
imperative that the safety guard be used.
2.3 r

Ating dAtA

2.3.1 s
pecificAtions
Voltage
Power Input
Power Output
Protection class
Type of protection
Overload protection
No-load speed
Sound pressure level
Threaded connection for flexible shafts of type:
DIN 10
NA 4, NA 7, NA 10, NA 12
NA 10 DIN 10/G28 STEP
NA 12 DIN 10 G28 STEP
2.3.2 V
iBrAtion mesurement VAlues of hAnd tools
BSG 10
Measurement value <2.5m/s
FSM 1:1
Measurement value 4.7m/s
WI 7, WI 10
Measurement value <2.5m/s
WH 12
Measurement value <2.5m/s
FH 12
Measurement value <2.5m/s
FH 10
Measurement value <2.5m/s
FH 7, FH 4
Measurement value <2.5m/s
According to ISO/EN 60745.
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.4 o
perAting conditions
Temperature range during operation: 0 to +50°C
Relative air humidity: 90% at +30°C, 65% at +50°C
1x230/240V - 50/60Hz, 8.9A
2000W
1650W
IP45
yes
500-13'000min
77dB(A), K=1.5m/s
M10
see catalog
03002613
03002912
Test grinding wheel ø 100x25
2
/K=1.5m/s
Drive 7'000min
Test grinding wheel ø 180x6
2
/K=1.5m/s
Drive 8'000min
Test grinding wheel ø 50x6
2
/K=1.5m/s
Drive 15'000min
Test grinding wheel ø 100x25
2
/K=1.5m/s
Drive 10'000min
Test grinding wheel ø 80x10
2
/K=1.5m/s
Drive 12'000min
Test grinding wheel ø 80x10
2
/K=1.5m/s
Drive 15'000min
Test grinding wheel ø 25x10
2
/K=1.5m/s
Drive 15'000min
To avoid strong looping movements and beaming
of the flexible shafts, the working pressure must
be reduced.
3.
handlIng
3.1 m

Achine

1 3.1.1 c
ontrol KeypAd
-1
2
Speed gauge (1). Speed correction «-/+» (2). Speed con-
2
firmation «enter» (3). «run» start command (4). «stop» stop
-1
command (5). ON/OFF «step» safety device (6).
2
3.1.2 s
tArting the mAchine
-1
Before turning on the machine, make sure to re-
move wrenches and adjusting tools.
2
When turning on, hold the flexible shaft extended.
-1
During operation make sure that the flexible shafts have
large bend radius.
2
Before starting the machine, hold the hand tool against
-1
turning!
Operate power switch of the machine.
2
Speed gauge blinking.
-1
Pre-select speed with key «-/+».
The speed gauge blinks until the pre-selection is con-
2
firmed with the «enter» key.
-1
The speed is saved.
If a start command is not issued within 60 seconds, the
2
speed gauge will start to blink.
-1
Now pre-select the speed again by pressing the «enter»
key.
Press the «run» key = Start the machine.
During operation the speed can be varied with the «-/+»
keys.
3.1.3 m
Achine stop
Press «stop» key.
Hold hand tool steady until the speed Zero is reached.
Speed blinks.
/ o
peratIon
35