Descargar Imprimir esta página

HQ-Power VDPLP64SB Manual Del Usuario página 3

Foco par64 corto con leds
Ocultar thumbs Ver también para VDPLP64SB:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

• Only use the device for its intended purpose. All other uses may lead to short circuits, burns,
electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty
and the dealer will not accept responsibility for any ensuing defects or problems.
• Mechanical wear is not covered by the warranty.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature.
Protect the device against damage by leaving it switched off until it has reached room
temperature.
• This device is designed for professional use on stage, in discos, theatres, etc. The
VD PLP6 4 SB/ VD PLP6 4 SC can be used in door s with an alternating current of max.
230VAC/50Hz.
• Lighting effects are not designed for permanent operation: regular operation breaks will prolong
their lives.
• Use the original packaging if the device is to be transported.
• Keep this manual for future reference.
4 . Fe a t u r e s
• RGB colour mixing
• output distance : 20-25m
• master / slave or sound activated
• DMX-controlled : 4 channels with dimmer / strobe function
• with built-in microphone for sound activation
5 .
I nst a lla t ion
a ) Fix t u r e
Choose a suitable mounting location and mount the light in the desired angle.
Use a waterproof cover when using the light outdoors.
Insert the power cord into an appropriate outlet (230VAC / 50Hz).
Switch off the power to the light when not in use.
This LED parcan is controlled through a 3-pin XLR (1
= GROUND, 2 = DATA-, 3 = DATA+).
b) Fu se
Only fit or replace a fuse when the device is
unplugged from the mains.
Replace a blown fuse with a fuse of the same type
and rating (see "Te chnica l Spe cifica t ion s"):
1. Remove the fuse holder (1) at the back using an
appropriate screwdriver.
2. Remove the old fuse and install a new one.
3. Replace the fuse holder and fasten tight with the
screwdriver.
c) M ou n t in g t h e D e vice
Have the device installed by a qualified person, respecting EN 60598-2-17 and all other
applicable norms.
The carrying construction must be able to support 10 times the weight of the device for 1
hour without deforming.
The installation must always be secured with a secondary attachment e.g. a safety cable.
Never stand directly below the device when it is being mounted, removed or serviced. Have a
qualified technician check the device once a year and once before you bring it into service.
Install the device in a location with few passers-by that is inaccessible to unauthorized
persons.
Overhead mounting requires extensive experience: calculating workload limits, determining
the installation material to be used... Have the material and the device itself checked
regularly. Do not attempt to install the device yourself if you lack these qualifications as
improper installation may result in injuries.
Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
Make sure there is no flammable material within a 0.5m radius of the device.
Have a qualified electrician carry out the electric connection.
Connect the device to the mains with the power plug. Do not connect it to a dimming pack.
The installation has to be approved by an expert before the device is taken into service.
27.09.2011
VD PLP6 4 SB / VD PLP6 4 SC
3
©Velleman nv

Publicidad

loading

Este manual también es adecuado para:

Vdplp64sc