Descargar Imprimir esta página

HQ-Power VDPLP64SB Manual Del Usuario página 4

Foco par64 corto con leds
Ocultar thumbs Ver también para VDPLP64SB:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

6 . Use
• Auto: DIP switches as below (X means ON, 0 means OFF)
M ode
10
9
0
0
Auto run
(master
projector)
0
0
Sound
activated
0
1
(master
projector)
DMX
1
X
1
0
Other
1
0
• D M X5 1 2 m ode :
Press 10 to ON to receive the DMX signal. 1-9 are used to select the requested address.
1
2
1
2
Example: If the start address should be 95 the settings would be (for switches 1-10):
1111101000 (1 + 2 + 4 + 8 + 16 + 0 + 64 = 95).
This unit has 4 channels. Refer to the functions below:
Ch 1 : 0-255 Red dimmer
Ch 2 : 0-255 Green dimmer
Ch 3 : 0-255 Blue dimmer
Ch 4 : 0-189 Dimmer
190-250 Strobe
251-255 No function
• D M X5 1 2 Con n e ct ion
Connect an XLR cable to the female 3-pin XLR output of your controller and the other side to the
male 3-pin XLR input of the VD PLP6 4 SB / VD PLP6 4 SC. Multiple VD PLP6 4 SB / VD PLP6 4 SCs can
be linked through serial linking. The linking cable should be a two-core screened cable with XLR
input and output connectors.
• D M X- 5 1 2 Ch a in w it h Te r m ina t ion
• Pr oj e ct or D M X st a r t a ddr e ss se le ct ion
All DMX-controlled devices need a digital start address so that the correct device responds to the
signals. This start address is the channel number from which the device starts to "listen" to the DMX
controller. Enter the correct number and read it from the display located on the base of the
VDPLP6 4 SB / VDPLP6 4 SC.
You can use the same starting address for a whole group of devices or enter an individual one for
every device.
When all devices have the same address, all the VDPLP6 4 SB / VDPLP6 4 SCs will "listen" to the
control signal on one particular channel. In other words: changing the settings of one channel will
affect all devices simultaneously. If you set different addresses, each device will "listen" to a
separate channel number. Changing the settings of one channel will only affect the device in
question.
In the case of the 4-channel VDPLP6 4 SB / VDPLP6 4 SC, you will have to set the start address of
the first VDPLP6 4 SB / VDPLP6 4 SC to 1, the second VDPLP6 4 SB / VDPLP6 4 SC to 5 (1 + 4), the
third to 9 (5 + 4) and so on.
27.09.2011
VD PLP6 4 SB / VD PLP6 4 SC
D I P
8
7
6
5
4
3
X
X
0
0
0
0
0
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
0
3
4
4
8
16
A DMX terminator is recommended for installations where the DMX cable has
to run a long distance or is in an electrically noisy environment (e.g. discos).
The terminator prevents corruption of the digital control signal by electrical
noise. The DMX terminator is simply an XLR plug with a 120Ω resistor
between pins 2 and 3, which is then plugged into the XLR output socket of
the last device in the chain.
Please see illustrations.
2
1
Colour changing and fading. Select running
0
0
Static colour and flash. Select colour via dip
X
X
1-3, and flash speed via dip 4-6.
X
X
Sound-activated colour change.
X
X
CH3 → B CH4 → Dimmer, strobe
1. DMX address is 1 when in DMX mode.
0
1
2. As slave projector when in M/S mode.
0
0
5
6
7
32
64
4
Fu n ct ion
speed via dip 7-8.
DMX mode
CH1 → R CH2 → G
Black-out
8
9
128
256
10
*
©Velleman nv

Publicidad

loading

Este manual también es adecuado para:

Vdplp64sc