Publicidad
3.4 Making Connections: Only use self‐locking snap hooks and carabiners with this equipment. Only use connectors that are suitable to each
application. Ensure all connections are compatible in size, shape, and strength. Do not use equipment that is not compatible. Visually ensure all
connectors are fully closed and locked. Connectors (snap hooks and carabiners) are designed to be used only as specified in each product's user's
instructions. See Figure 13 in Appendix B.
3.5 Personal Fall Arrest System: A PFAS is an assembly of components and subsystems used to arrest a person during a fall event. See paragraph
2.2. The fall arrest system that is used with the unit discussed in this manual will require an approved fall arrest anchor.
3.5.1 Anchorage Strength: An anchorage selected for PFAS must have a strength able to sustain a static load applied in the direction permitted by
the PFAS of at least:
a)
Two times the maximum arrest force permitted when certification exists, or
b)
5,000 lbs. (22.2 kN) in the absence of certification.
An anchorage selected for work positioning must be able to withstand a load of twice the potential impact load of a falling user, or 3,000 lbs,
(13.34 kN) whichever is greater.
3.6 Definitions: The following are definitions of terms.
Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard
(otherwise referred to as "user" for the purpose of these instructions).
Certified Anchorage: An anchorage for fall arrest, positioning, restraint, or rescue systems that a qualified person certifies to be capable of supporting the
potential fall forces that could be encountered during a fall or that meet the criteria for a certified anchorage prescribed in this standard.
Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are
unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
Harness Stretch: Amount of vertical travel of the Full Body Harness D‐ring during a fall arrest.
Qualified Person: A person with a recognized degree or professional certificate and with extensive knowledge, training, and experience in the fall
protection and rescue field who is capable of designing, analyzing, evaluating and specifying fall protection and rescue systems to the extent
required by this standard.
Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.
4. INSTALLATION AND OPERATION
Do not alter or intentionally misuse this equipment. Consult FallTech when using this equipment in combination with components or
Do not use rebar hooks, large carabiners or large snap hooks to connect to the FBH dorsal D‐rings or to any small diameter non‐compatible
Use caution and take action to avoid excessively sharp and/or abrasive surfaces and edges.
Avoid electric hazards. Use caution when performing arc welding. Arc flash from arc welding operations, including accidental arcs from electrical
Examine the work area. Be aware of the surroundings and workplace hazards that may impact safety, security, and the functioning of fall arrest
systems and ancillary components. Hazards may include but not be limited to cable or debris tripping hazards, equipment failures, personnel
mistakes, moving equipment such as carts, barrows, fork lifts, cranes, or dollies. Do not allow materials, tools, or equipment in transit to
contact any part of the anchor or fall arrest system and/or ancillary components. Pay special attention to the lifeline. Do not work under
4.1. Install and Use the RPL: Proper installation and use of the RPL must be ensured by a competent person. The authorized person must read,
understand, and follow the instructions in this manual and all labels on the product before using this product. The RPL discussed in this manual is a
work positioning device and does not function as a fall arrest device. The SAL, the SRD, or the VLL is the fall arrest device in the fall protection
system. Rig the RPL so the fall arrest system will engage and arrest the fall before the RPL becomes impacted.
The PFAS and the RPL require the use of an FBH. Ensure connectors are compatible.
The unit discussed in this manual may also be used as a climbing device on poles or other similar structures. Know the distance between the rope
adjuster and the nearest obstruction below or to the lower level. Ensure no fall arrest impact loads will be placed on the RPL.
Consult the user instruction manual for the primary PFAS in use for details of fall clearance calculation requirements.
Inspect the RPL before each use in accordance with the procedures defined in Section 7 of this manual. Do not use the RPL if inspection shows
damage or any malfunction. Don the FBH in accordance with the FBH manufacturer's instructions. Connect the PFAS to the dorsal D‐ring of the
FBH, and attach the PFAS to an approved anchor.
The work position may be altered via the rope adjuster. The rope adjuster uses a rope adjustment cam to lock onto the rope. The lanyard may be
drawn tighter through the closed cam by pulling the rope up through the adjuster. To slack the rope and add length to the RPL, tilt the rope
adjuster up, press the thumb lever to release the cam and allow the rope to slide through the rope adjustor. Release the thumb lever to lock the
rope adjuster in position on the rope. See Figure 3.
To use the RPL, attach the rope end termination connector to a side D‐ring of an FBH. Pass the RPL around the work positioning anchorage
structure. Some structures may be more prone to the RPL slipping down the structure. In this case, pass the RPL around the structure again. Ensure
there are no sharp edges or abrasive surfaces. Ensure the protective sleeve protects the rope against contact with the structure. Attach the rope
adjuster carabiner to the other FBH side D‐ring. Get into the work position. Situate the rope adjuster to create a comfortable amount of tension to
allow the use of tools without holding onto the rope. Allow the free end of the rope to hang freely. The RPL may be drawn tighter or slacked off as
the user requires using the rope adjuster. See Figure 4.
CAUTION: Work safely and take precautions when working above the PFAS anchor.
DO NOT place yourself in a position where a fall event will impact the RPL before the PFAS engages.
DO NOT allow the RPL line to become slack.
DO NOT disconnect the PFAS from the FBH dorsal D‐ring.
DO NOT use the lanyard without both connectors connected to the FBH side D‐rings.
DO NOT use the RPL without a backup PFAS.
subsystems other than those described in this manual.
anchor point as this may cause a roll‐out condition and/or unintentional disengagement.
equipment, can damage equipment, cause severe injury and are potentially fatal.
WARNING
suspended loads.
3
032515
Publicidad
