Introductory Comment; General Rules Of Safety; Before Use; Handling Of The Packed Machine - Tornado 99790 Manual De Operaciones Y Mantenimiento

INTRODUCTORY COMMENT

Your new Tornado unit is a high qual-
ity, precision-made product. All parts
used in the manufacturing of this
unit have passed rigid quality control
standards prior to assembly. Please
safeguard the original receipt / invoice.
If you experience any problems with
your unit during the warranty period,
the original receipt / invoice will act as
proof of purchase. Contact Tornado for
any warranty inquiries.

GENERAL RULES OF SAFETY

The rules below have to be followed
carefully in order to avoid injury to the
operator and damage to the machine.
− Read the labels carefully on the
machine. Do not cover them for any
reason and replace them immediately
if damaged.
− ATTENTION: The machine must be
used only by authorized staff that have
been instructed on its correct and
proper use.
− ATTENTION: Do not use the ma-
chine on areas having a higher gradi-
ent than the one stated on the number
plate.
− ATTENTION: The machine is not to
be used by persons, children included,
with reduced physical, sensorial or
mental capabilities, or with lack of
experience or knowledge, unless they
could benefit, through the intermedia-
tion of a responsible person for their
safety, by a supervision or instructions
concerning to its use.
− During the operation of the machine,
pay attention to other people and es-
pecially to children.
− Children shall not play with the
machine.
− Children cannot carry out cleaning
and maintenance of the machine.
TRANSFER
− Do not strike shelvings or scaffold-
ings where there is danger of falling
objects.
− Leaving the machine in parking
position, remove the key and apply the
parking brake.
− Do not use the machine as a means
of transport.
− Adapt the working speed to the con-
ditions: particularly, slow down before
facing narrow curves.
STORAGE AND DISPOSAL
− Storage temperature: between 32°F
and 131°F (0°C and +55°C).
− Perfect operating temperature:
between 32°F and 104°F (0°C and
+40°C ).
− The humidity should not exceed
95%.
− Provide for the scrapping of the
material of normal wear (brushes,
squeegee blades etc.) following the
respective rules.
When your machine has to stop
activity, provide for the appropriate
waste disposal of its materials, es-
pecially oils, batteries and electronic
components, and considering that
the machine itself has been, where
possible, constructed using recyclable
materials.
CORRECT USE
− Do not use the machine on surfaces
covered with inflammable liquids or
dusts (for example hydrocarbons,
ashes or soot).
− In case of fire, use a powder based
fire-extinguisher. Do not use water.
− Do not use the machine in explosive
atmosphere.
− The machine has to carry out simul-
taneously the operations of washing
and drying. Different operations must
be carried out in restricted areas
prohibited to non-authorized personnel
and the operator has to wear suitable
shoes.
− Signal the areas of moist floors with
suitable signs.
− Do not mix different detergents,
avoiding harmful odours.
− Avoid brushes operation when the
machine is standing still in order to
prevent floor damages.
MAINTENANCE
− If the machine does not work
properly, check by conducting simple
maintenance procedures.
Otherwise, ask for technical advice
from an authorized assistance center.
− For any cleaning and/or mainte-
nance operation remove the power
supply from the machine.
− Where parts are required, ask
for ORIGINAL spare parts from the
distributor and/or from an authorized
dealer.
− Use only ORIGINAL brushes
indicated in the paragraph "RECOM-
MENDED BRUSHES".
8
− Do not take off the protections
which require the use of tools for their
removal.
− Do not wash the machine with direct
water jets or with high water pressure
nor with corrosive material.
− Every 200 working hours have a ma-
chine check by an authorized service
department.
− Before using the machine, check
that all panels and coverings are in
their position as indicated in this use
and maintenance catalogue.
− Restore all electrical connections
after any maintenance operation.

BEFORE USE

HANDLING OF THE PACKED MA-
CHINE
The machine is supplied with suit-
able packing foreseen for fork lift truck
handling.
The total weight is:
1433 lbs. ( 650kg)
Packing dimensions:
Base: 84" x 45" (213 cm x 115 cm)
Height: 65" (165 cm)
Do not place any packings on top.

UNPACKING OF THE MACHINE

1. Remove the external packing.
2. Move the machine backwards, as
indicated in the figure, avoiding heavy
contacts to mechanical parts.
3. Keep the pallet for eventual trans-
port.
ACCESS TO THE BATTERY COM-
PARTMENT
1. Bring the machine on a levelled
surface.
2. Rotate the seat platform forward up
to the blocking of the support.
3. Having finished any intervention, to
close the battery compartment, after
having released the support, reposi-
tion the seat platform.