Wall Mounting; Assembly And Adjustments; Intended Use - DeWalt DCW210 Manual De Instrucciones

ENGlIsh
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting


DCB107, DCB112, DCB113, DCB115, DCB118,
DCB132
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

Intended Use

This random orbit sander has been designed for sanding
wood, metal, plastics and painted surfaces.
Do NoT use under wet conditions or in presence of
flammable liquids or gases.
Do NoT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Attaching Sanding Discs (Fig. B)
Your sander is designed to use 5" (127 mm) sanding discs
with an 8-hole dust extraction pattern. Sanding discs for the
DCW210 attach with hook and loop.
The recommended DWE64233 sanding discs are available
at extra cost from your local dealer or authorized D
service center.
32
To Attach Sanding Disc to the Sanding
Pad (Fig. B)
1. Turn the sander over so that the sanding pad
facing upward.
2. Clean the dust from the sanding pad
3. Hold the pad with one hand to keep it from rotating.
4. With the other hand, align the holes and place the
disc 9 directly on top of the pad.
NoTE: These sanders are not to be used in drywall
applications. Using a sanding screen (e.g., screen used for
sanding drywall) directly on the hook and loop pad will not
hold and will damage the hooks on the pad. The hooks on
the pad will wear very rapidly if left in contact with the work
surface while the tool is operating.
Fig. B
Dust Extraction (Fig. C, F)
Your sander has two dust extraction methods: a built-in
dust port 3 which allows either the supplied dust bag
a shop vacuum system to be connected; and a dust
skirt ( , Fig. F). The built-in dust port utilizes the D
10
AirLock connection making it compatible with the D
dust extractors.
To Attach the Dust Bag (Fig. C)
1. While holding the sander, fit the dust bag collar
the dust port
2. Turn the collar
in place.
Fig. C
9
WALT
e
face.
6
9
3 as shown in Figure C.
5 clockwise to lock the dust bag
4 5
6 is
6
4 or
WALT
e
WALT
e
5 to
4
3