Starmix GS Serie Instrucciones Para El Manejo página 9

GB
I. Model GS/HS PA-1455
Mount the wheels on the trolley crossbar.
[Tighten] wheels with fastener in front Z.
II. Mount the run-off angle
Remove the lock S on the reflux valve
Loosen the run-off angle
The reflux valve has to be mounted.
1. Mounting the tank with the pump
1.1. Insert the pump into the tank.
1.2. Screw the run-off angle
sleeve B (I).
1.3.
Fasten the pump with the cable binder D on the
inside of the tank (I).
1.3.1. Remove the blind plug H and blind coupling G
refer to routine
1.4. Press out the cable stopper J from the cable outlet C.
Lead the connecting cables for the pump through the
cable outlet C.
1.5.
Put the cable stopper J over the pump cables on the
outside, push forward to the tank and press firmly into
the cable outlet C
1.6. Connect the vacuum hose E and runoff hose F to
the tank.
1.7. Insert the connecting cables of the pump into the
socket K on the vacuum
2. Retrofitting the pump vacuum cleaner/water
vacuum cleaner to a wet/dry vacuum cleaner
2.1. Remove the plug to the pump on the vacuum
2.2. Disassemble the cable stopper from the flange 1 + 1'
and pull the connecting cables of the pump through
flange 2 (II).
2.3. Loosen the cable binder D
2.4. Unscrew the run-off angle
2.5.
Take the pump from the tank.
2.6. Firmly press the cable stopper J into the cable outlet
C again.
2.7.
Press the blind plug H into cable stopper J to the
2.8. Screw the blind coupling G on the runoff opening M.
You can now use the vacuum cleaner as a
conventional wet/dry vacuum cleaner
(without tilt trolley)
A on pump B/1.
B/2.
A B/3, B/4.
A onto the tank thread
1.3.1. a–d.
(I).
cleaner.
(II).
A from the thread sleeve B
3. Operating the pump vacuum cleaner
Also refer to the instructions for use for the wet/dry
vacuum cleaner.
3.1. Remove the folded filter
– unlock the bayonet seal on the underside of the filter.
– remove the folded filter downward from the filter
basket.
3.2. Carefully pull the blue foam filter over the filter
Refer to Item 5.2 of the operating instructions for
the HS vacuum cleaner.
3.3. Lead the runoff hose F into a water drain/gully hole
or a suitable area outside.
3.4. Plug the connecting cables of the pump into the
vacuum cleaner socket
When the pump is plugged in, the pump carries
out a brief self-test.
3.5. Turn on the vacuum cleaner by turning the rotating
switch to ››I‹‹.
3.6. Suction water with the vacuum hose E
mounted accessories).
The pump automatically pumps the suctioned water
off over the runoff hose
when it reaches a certain water level.
3.7. There is a certain amount of water left in the
tank for technical reasons after completing
water vacuuming.
You can
a) empty all of this residual water by spilling it off, or
b) remove some of this residual water from the tank by
repeatedly pulling out and inserting the pump power
plug on the vacuum head.
head.
3.8. If you want to separate course
≥ 0.5 mm) from water (for instance, when cleaning
ponds including thread algae), we recommend using the
supplied FSN 80 filter sack (424071).
3.9. If you want to separate fine
from water, we recommend using the NFB wet
(II).
filter bag
The maximum pump passage size =
10 mm
systems.
The pump can get clogged due to thread algae. Refer
catch.
to 4.4 for cleaning.
cartridge.
K.
F with a built-in level switch
dirt (grain size < 0.5 mm)
(420592).
when vacuuming without these two filter
basket.
(and any
dirt (grain size
grain size
9