Hisense HMO173SR Guía De Uso Y Cuidado página 10

Ocultar thumbs Ver también para HMO173SR:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2.Beneath framed recessed cabinet
TOP LINE OF REAR WALL TEMPLATE
Must align with the back frame of
cabinet bottom
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. Use a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R eturn to and proceed with the installation
instructions.
TOP LINE OF REAR WALL TEMPLATE
TOP LINE OF REAR WALL TEMPLATE
Trim the rear wall template along the dotted line.
10
Step-by-step installation guide
Back frame of
F.CUT OUT FOR
HORIZONTAL
OUTSIDE EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. Use a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R eturn to and proceed with the installation
instructions.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTER LINE.
MARK THE LOCATION FOR 2 ADDTIONAL,EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
A
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
4 "
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. Use a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
REAR WALL TEMPLATE
4. Return to and proceed with the installation
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF THE CENTER LINE.
MARK THE LOCATION FOR 2 ADDTIONAL,EVENLY SPACED TOGGLE BOLTS IN THE
MOUNTING PLATE AREA.
Trim the rear wall template along the dotted line.
A
F.CUT OUT FOR
HORIZONTAL
OUTSIDE
EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
REAR WALL TEMPLATE
C
Rear
F.CUT OUT FOR
HORIZONTAL
OUTSIDE
EXHAUST
CUT HOLE THROUGH REAR WALL
FOR EXHAUST ADAPTOR
1 2
CAUTION -IF EXHAUST ADAPTOR
IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, G
REASE-LADEN AIR WILL
DISCHARGE INTO
HOUSE STRUCTURE
3 0 "
M I N I M U M
W I D T H
R E Q U I R E D
B
C
B
Front

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido