Hisense HMO173SR Guía De Uso Y Cuidado página 11

3 Beneath framed recesse bottom cabinet with front overhang
.
TOP LINE OF REAR WALL TEMPLATE
Must align with below cabinet bottom the same distance as the front overhang of cabinet
bottom.
below cabinet bottom the same
distance as the front overhang of
cabinet bottom
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. U se a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R eturn to and proceed with the installation
instructions.
TOP LINE OF REAR WALL TEMPLATE
TOP LINE OF REAR WALL TEMPLATE
Your cabinets may have decorative trim that interferes with the
microwave installation. Remove the decorative trim to install the
microwave properly and to make it level.
THE MICROWAVE MUST BE LEVEL
Use a level to make sure the cabinet bottom is level. If the cabinets have a
front overhang only,with no back or side frame, top line of rear wall template
must align with below cabinet bottom, the same distance as the front overhang
depth.this will keep the microwave level.
1.Measure the inside depth of the front overhang.
2.Draw a horizontal line on the back wall an equal distance below the cabinet
bottom as the inside depth of the front overhang.
3.For this type of installation with front overhang only,align top line of rear wall
template with this horizontal line, not touching the cabinet bottom as described
in step D.
Step-by-step installation guide
Front overhang
of cabinet
bottom
F.CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
4"
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. Use a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R eturn to and proceed with the installation
instructions.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTER LINE.
MARK THE LOCATION FOR 2 ADDTIONAL,EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
A
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
BEFORE PROCEEDING WITH THIS F.CUT OUT FOR HORIZONTAL
REAR WALL TEMPLATE.
4"
OUTSIDE EXHAUST
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust. CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
1.Tape the template to the rear wall.
2. U se a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R eturn to and proceed with the installation
instructions.
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION，GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
REAR WALL TEMPLATE
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTER LINE.
MARK THE LOCATION FOR 2 ADDTIONAL,EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
A
3/8" TO EDGE
12"
6"
F.CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION，GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
REAR WALL TEMPLATE
30" MINIMUM WIDTH REQUIRED
C
Front
Rear
6"
B
C
B
11