Descargar Imprimir esta página

Fein KBU 35 Q Manual De Instrucciones página 29

Ocultar thumbs Ver también para KBU 35 Q:

Publicidad

OBJ_BUCH-0000000256-001.book Page 29 Wednesday, May 4, 2016 9:43 AM
Character
Unit of measure-
ment, international
m/s
m/s
h
m, s, kg, A, mm,
V, W, Hz, N, °C,
dB, min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
Magnetic core drill unit for drilling with core drill bits and
solid drill bits, reaming, countersinking and tapping on
materials with surfaces suitable for magnets in weather-
protected environments using the application tools and
accessories recommended by FEIN.
This power tool is also suitable for use with AC genera-
tors with sufficient power output that correspond to the
Standard ISO 8528, design type G2. This Standard is par-
ticularly not complied with when the so-called distortion
factor exceeds 10 %. When in doubt, please refer to the
generator instruction/specification guide.
These appliances are not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
Special safety instructions.
Wear personal protective equipment. Depending on the
application, use a face shield, safety goggles or safety
glasses. Wear ear protection. The safety glasses must be
capable of protecting against flying particles generated by
the various different operations. Prolonged exposure to
high intensity noise may cause loss of hearing.
Do not touch the sharp edges of the core drill bit. Danger
of injury.
Replace the protective cable bushing immediately when
damaged. A defective protective cable bushing can lead
to overheating of the machine and to an emergency stop.
Before putting into operation: Mount the contact protec-
tor to the machine.
Unit of measure-
ment, national
2
2
m/s
2
2
m/s
m, s, kg, A, mm,
V, W, Hz, N, °C,
2
dB, min, m/s
Always secure the power tool with with the supplied lash-
ing strap. In case of a power failure or when the mains
plug is pulled, the magnetic holding power is not main-
tained. When carrying out such work, beware of falling
objects, such as cores or chips.
When working overhead or on vertical surfaces, the cool-
ant container must not be used. Use a coolant spray
instead. Liquids penetrating your electric power tool may
cause electric shock.
Avoid touching the drilled core that is automatically
ejected by the centering pin when the working procedure
is finished. Contact with the core when it is hot, or if it
falls, can cause personal injuries.
Operate the power tool only from grounded sockets that
comply with the specifications. Do not use any connection
cables that are damaged; use extension cables with a
grounding contact that are checked at regular intervals.
A ground conductor without continuity can cause an
electric shock.
To prevent injuries, always keep your hands, clothing,
etc. away from rotating swarf. The swarf can cause inju-
ries. Always use the chip guard.
Do not attempt to remove the cutting tool if it still turns.
This can lead to serious injuries.
Hold power tool by the insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting acces-
sory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the opera-
tor an electric shock.
Beware of any concealed electric cables, gas or water
conduits. Check the working area before commencing
work, e. g. with a metal detector.
Do not machine any material containing asbestos. Asbes-
tos is cancerogenic.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Do not overload the power tool or the storage case and do
not use it as a ladder or stand. Overloading or standing
on the power tool or the storage case can lead to the
upward shifting of the centre of gravity of the power tool
or the storage case, and its tipping over.
Do not use accessories which are not specifically
designed and recommended by the power tool manufac-
turer. Safe operation is not ensured merely because an
accessory fits your power tool.
Explanation
Vibrational emission value according to
EN 60745 (vector sum of three directions)
Mean vibrational value for core drilling
Basic and derived units of measurement from
the international system of units SI.
2
en
29

Publicidad

loading

Este manual también es adecuado para:

Kbu 35 mqKbu 35-2 q