Operation - RIDGID GP80145SW Manual Del Operador

OPERATION

DANGER:
Do not disassemble pressure unloader, tank drain
valves or safety relief valve with air in tank — bleed
tanks.
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes resulting in possible serious injury.
WARNING:
Never direct a jet of compressed air toward people
or animals. Take care not to blow dust and dirt
towards yourself or others. Following this rule will
reduce the risk of serious injury.
NOTICE:
Do not use in an environment that is dusty or
otherwise contaminated. Using the air compressor
in this type of environment may cause damage to
the unit.
APPLICATIONS
Air compressors are utilized in a variety of air system
applications. Match hoses, connectors, air tools, and
accessories to the capabilities of the air compressor.
You may use this product for the purposes listed below:
 Operating some air-powered tools
 Operating air accessories such as air nozzles and tire
inflators
ADDING/CHECKING ENGINE OIL
See Figures 6 - 7, page 20.
NOTE: This machine has been shipped with approximately
2 oz. of oil in the engine from testing. You must add oil to
the engine before starting it the first time.
NOTICE:
Any attempt to start the engine without adding oil
will result in engine failure.
To add engine oil:
 Place air compressor on a flat, level surface.
 Unscrew the engine oil cap/dipstick by turning counter-
clockwise.
 Before first use, pour the entire contents of the oil bottle
provided into the oil reservoir.
After initial use, add 4-stroke engine oil (SAE 30 or SAE
10W30) until the fluid level rises between the hatched
area on the dipstick. Do not overfill.
NOTE: Avoid using too much oil. Ensure that the level of
the oil does not rise above the upper hatched area.
 Replace the engine oil cap/dipstick and securely tighten.
NOTE: This engine has a total oil capacity of 20 oz. (0.6 liters).
To check engine oil level:
 Set engine on a flat surface.
 Remove engine oil cap/dipstick.
 Wipe engine oil cap/dipstick clean and re-seat in hole.
Do not rethread.
 Remove engine oil cap/dipstick again and check oil level. Oil
level should be between the hatched area on the dipstick.
 If level is low, add engine oil until the fluid level rises to
the upper portion of the hatched area on the dipstick.
 Replace and secure the engine oil cap/dipstick
NOTICE:
Do not overfill. Overfilling the crankcase may cause
excessive smoke and engine damage.
OXYGENATED FUELS
DO NOT USE E85 FUEL. IT WILL VOID YOUR WARRANTY.
NOTE: Fuel system damage or performance problems
resulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated below are not
covered under warranty.
Ethanol. Gasoline containing up to 10% ethanol by volume
(commonly referred to as E10) is acceptable. E85 is not.
ADDING/CHECKING PUMP OIL
See Figure 8, page 20.
 Unscrew the pump oil cap/dipstick by turning counter-
clockwise.
 Before first use, pour the entire contents of the pump oil
bottle provided into the oil reservoir.
After initial use, add pump oil until the fluid level rises
between the MIN and MAX reference levels on the
dipstick. Do not overfill.
NOTE: Avoid using too much oil. Ensure that the level of
the oil does not exceed the maximum reference mark on
the dipstick.
 Replace the pump oil cap/dipstick and securely tighten.
NOTE: This pump has a total oil capacity of 30 oz. (887.2ml).
10 – English