Calibration Menu - Bosch WBE 5210 Instrucciones De Reparacion

4. Use configuration
To enter the use configuration menu, press „SET" until
when the notice "SET" will appear on the left display.
Now, using „SET" you can surf the menu to configure
the machine according to the final user's needs; in or-
der to change values, use + and – DIAMETRE.
Here are the values set in the production phase.
Left Display Right Display Description
TOL 5
RES 5
UNB GRA
SND ON
CAR ON
LAR 0.50
5. Configuration of the board
We use the same kind of cpu board for every version
of SBM125-150 (code 653756). If in case of assist-
ance, for any reason, you had to substitute it, you will
need to check and turn on the specific functions of the
machine.
To enter the use configuration menu, press „SET" until
the notice SET will appear on the left display and after
1.5s max, press „MM/INCH". Finally, in order to change
values use + and –. To confirm, press OK.
Here you are the possible functions following the ver-
sion:
Left Display Right Display Description
POT OFF/ON
ALU OFF/ON
PED OFF/ON
PLR OFF/ON
ROT OFF/ON
Robert Bosch GmbH
It indicates the threshold of
the zeroing of the machine
Identification of the unbal-
ance, rounded off to 5g or real
Selection of the weight
(grams or once)
It indicates the acous-
tic sound (beep)
It indicates the possibility to use
the protecting carter for the launch
Visualization of the width:
0.50" or 0.25"
Turn on/off the inter-
nal automatic gauge
Turn on/off the gauge func-
tion called "aludata"
Turn on/off the function to read
the data through the pedal
Turn on/off the width gauge
Turn on/off the function to meas-
ure the eccentricity of the wheel
through the sonar (by request)
Use confi guration | WBE 5210 | 21
NOTES FOR THE ASSISTANCE:
Here you are the settings belonging to the SBM 855
versions:
Left Display Right Display
POT OFF
ALU OFF
PED OFF
PLR OFF
ROT OFF
6.

Calibration menu

The procedure of the machine calibration is divided in
three different parts:
+
Calibration of the flange
+
Calibration of the electronic gauges,
+
Self-calibration with wheel and sample weight
The calibration of the flange memorizes the value of
unbalance of the shaft and adapter group for the wheel.
We suggest making the calibration of the flange in the
following cases:
+
when making a launch without the wheel, the ma-
chine has unbalances higher than 5 grams,
+
when you move from a flange to another (motorcycle
flange, cone-flange or 3\4\5 holes).
To enter the calibration menu, press „SET" until when
the notice "CAL " will appear on the left display and
after 1.5s max, press „MM/INCH". Now the left display
will show the notice "C-1".
Left Display Right Display Description
C-1
Flange calibration
Make a launch without the wheel to memorize the un-
balance of the flange group; this allows to compensate
electronically for possible unbalances left from the
shaft of the machine.
When the left display shows "C-2", it is possible to start
directly from the calibration with the wheel without
calibrate the flange before, simply by entering in the
calibration menu and pressing „SET" again.
Quando il display di sinistra mostra "C-2", è possibile
partire direttamente dalla taratura con la ruota senza
dover prima fare la taratura della flangia, semplicemen-
te entrando nel menù di taratura e premendo nuova-
mente il tasto SET.
Left Display Right Display Description
C-2
Memorization of the ze-
ro group flange and shaft
Setting up of the wheel size and
memorization of the unbalance
|
1 695 654 761 2008-10-17
en