Specific Safety Information; Press Tool Safety; Description And Specifications Description - RIDGID RP 340 Manual De Instrucciones

RP 340 Press Tool

Specific Safety Information

WARNING
This section contains important safety information
that is specific to this tool.
Read these precautions carefully before using the
RP 340 Press Tool to reduce the risk of electrical
shock or serious personal injury.
SAVE THESE INSTRUCTIONS!
A compartment in the RP 340 carrying case is included to
keep this manual with the machine for use by the operator.

Press Tool Safety

• Use the RP 340 Press Tool only with RIDGID
stand ard pressing attachments (jaw set, press
ring, actuator, etc.). Other uses or modifying the RP
340 Press Tool for other applications may damage
the press tool, damage the attachments and/or cause
personal injury.
• Keep your fingers and hands away from attach-
ments during press cycle. Your fingers or hands
can be crushed, fractured or amputated if they become
caught in the attachments or between these compo-
nents and any other object.
• Never attempt to repair a damaged jaw set, press
ring, actuator or other attachment. An attachment
that has been welded, ground, drilled or modified in
any manner can shatter during pressing resulting in
serious injury. Discard the entire damaged attach-
ment. Replace with a new jaw set. Never replace
individual components except for damaged jaw return
springs. Please call Ridge Tool Technical Service
Department for availability.
• Large forces are generated during product use
that can break or throw parts and cause injury.
Stand clear during use and wear appropriate protective
equipment, including eye protection.
• Only use RIDGID Press Tools and Jaws when
specified by the press fittings manufacturer. Use of
incorrect equipment and methods can cause incom-
plete joints, damage the equipment, void warranties or
cause severe personal injury or death.
• Before operating a RIDGID RP 340 Press Tool,
read and understand:
– This operator's manual,
– The attachment instructions,
– The battery/charger manual,
– The RPA 120/220 AC Power (Mains) Adapter In -
structions,
– The fitting manufacturer's installation instructions,
4
– The instructions for any other equipment used with
this tool,
Failure to follow all instructions and warnings may
result in property damage and/or serious injury.
The EC Declaration of Conformity (890-011-320.10) will
accompany this manual as a separate booklet when
required.
If you have any question concerning this RIDGID
– Contact your local RIDGID distributor.
– Visit www.RIDGID.com or www.RIDGID.eu to find
your local RIDGID contact point.
– Contact Ridge Tool Technical Service Department at
rtctechservices@emerson.com, or in the U.S. and
Canada call (800) 519-3456.
®
Description and Specifications
Description
The RIDGID ® RP 340 Press Tool, when used with appro-
priate jaw sets, is designed to mechanically press fit-
tings onto tubing to create a water-tight and permanent
seal. When the switch on the RP 340 is depressed, an
internal electric motor powers a hydraulic pump which
forces fluid into the cylinder of the tool, forcing the ram for-
ward and applying thousands of pounds of pressing force
onto specially designed fittings. Attachments are also
available for other uses.
The entire cycle duration is approximately five (5) seconds.
Once the cycle begins to deform a fitting, it will automat-
ically continue until completion, even if the trigger switch
is released. The LED displays on the top of the tool indi-
cate problems such as improper temperature, open jaw
mounting pin or maintenance required.
ON/OFF
Button
LED Display
Panel
Pressure
Release
Button
Tool Housing
Figure 1 – RP 340 Press Tool and Jaw Set
The tool is equipped with a bright LED work light that lights
up when the trigger is pulled and remains lit four (4) min-
Attachment
Jaw Arm
Warning
Mounting Pin
Label
LED
Work Light
Switch
Handle
Battery
® product:
Jaw
Sideplate
Scissor Style
Jaw Set