General Instructions - Vitamix MIX'N MACHINE Frozen Treat Mixer Manual Del Usuario

1. Put product (ice cream, yogurt, etc.) into a sturdy
serving cup along with ingredients such as liquid
flavoring, and mix-ins such as candy, cookies, fruit or
other condiments.
2.
For units with a Removable Agitator:
agitator up onto the shaft until it snaps into place.
3. Plug the machine into the nearest outlet (if unplugged).
4. Place a cup guard on the cup (See Figure 1). Hold the
cup (and lid or collar) securely in your hand
side, not from the bottom)
splash guard. Move the cup under the agitator and lift
up so the agitator touches the bottom of the cup. See Figure 2.
5. Turn the machine ON to activate the agitator. Follow instructions based
on the specific model:
•
For Mix'n Machine
Programmable Model:
(I/O) power switch to ON. Activate a
program by selecting the desired setting on
the dial. While holding the cup securely in
your hand, use your fingers to push the
START Actuator (located behind the
agitator) to activate a programmed
blending cycle. See Figure 3.
•
For Mix'n Machine Advance Timer
Press the ON/OFF (I/O) power
Model:
switch to ON. While holding the cup
securely in your hand, use your fingers to
push the START Actuator (located behind
the agitator) to activate a pre-set timed
blending cycle. See Figure 3.
•
For Mix'n Machine Advance Variable
Select the desired setting
Speed Model:
on the speed dial. While holding the cup
securely in one hand, use the other hand to
press the ON/OFF (I/O) power switch to ON
to activate the agitator. Depending on
ingredients, start on a lower setting, then
switch to a higher setting once the mixture
begins processing. (Foot pedal operation:
see page 6.)
•
For Mix'n Machine Standard Model
(Countertop and Wall Mount):
holding the cup securely in one hand, use
the other hand to press the ON/OFF (I/O)
power switch to ON to activate the agitator.
(Foot pedal operation: see page 6.)
6. With a swirling motion, gradually move the cup
up and down around the spinning agitator and
completely around all sides of the cup. (If ice
cream is hard, this should be done slowly.)
Develop your own technique for the desired
consistency of the finished product. The
agitator will do some chipping and breaking of
the solids. However, it is not intended to
completely pulverize ingredients as solid
chunks are expected to be evident in the final
product. See Figure 4.

GENERAL INSTRUCTIONS

Disposable Lid
push the
Permanent
Collar
*Cup guards are sold
through foodservice
(from the equipment distributors.
and reach under the
Figure 1
Advance
Press the ON/OFF
ON
OFF
ADVANCE PROGRAMMABLE ICE CREAM MIXER
Figure 2
ON
OFF
ADVANCE PROGRAMMABLE ICE CREAM MIXER
Figure 3
While
ON
OFF
ADVANCE PROGRAMMABLE ICE CREAM MIXER
Figure 4
Notes:
• Should the cup be hard to hold, either move the agitator into the
mix more slowly or start with softer ice cream.
to operate if you are having trouble holding the cup.
• Both the permanent agitator and the removable agitator are
designed to reduce the possibility of damage when contacting a
paper cup. However, they should not be forced or held solidly
against the side or bottom of the cup. The hard ice cream agitator
is specially designed to mix the product aggressively and
thoroughly, so use of a cup holder or sturdy cup is recommended
to prevent the agitator from going through the side of the cup.
7. Swirl the cup around the agitator to produce a pleasing product
appearance and to avoid leaving a hole in the center of the mixture.
Before removing the cup, allow excess mixture to be thrown off the
agitator and be caught by the cup or lid/collar. Follow machine shut-off
instructions based on the specific model:
• For Mix'n Machine Advance Programmable Model:
machine will shut off automatically at the end of the programmed
cycle. When the program is within 4 seconds of completion, the red
Indicator light will blink so preparation can begin to remove the
cup from the agitator. The blinking light will
get progressively faster to indicate that the
program cycle is almost complete and the
machine will shut off. This provides an
indication, so that excess product can be
spun off the agitator. See Figure 5.
•
For Mix'n Machine Advance Timer
The machine will shut off
Model:
automatically at the end of the pre-set time.
When the program is within 4 seconds of
completion, the red Indicator light will blink
so preparation can begin to remove the cup
from the agitator. The blinking light will get
progressively faster to indicate that the
program cycle is almost complete and the
machine will shut off. This provides an
indication, so that excess product can be
spun off the agitator. See Figure 5.
•
For Mix'n Machine Advance Variable
Press ON/OFF (I/O) power
Speed Model:
switch to OFF to stop the machine. See
Figure 6.
• For Mix'n Machine Standard Model
(Countertop and Wall Mount):
ON/OFF (I/O) power switch to OFF to stop
the machine. See Figure 6.
8. Press the ON/OFF (I/O) switch to OFF when not in use.
To use the PULSE switch to refresh drinks and desserts (Advance
Programmable Model only):
under the agitator and lift up so the agitator touches the bottom of the
cup. Depress the PULSE switch to start the agitator. With a swirling
motion, gradually move the cup up and down over the spinning agitator
and completely around all sides of the cup. Swirl the cup around the
agitator to produce a pleasing product appearance and to avoid leaving
a hole in the center of the mixture. Before removing the cup, allow excess
mixture to be thrown off the agitator and be caught by the cup or
lid/collar. Release the switch to stop the agitator.
4
DO NOT
Indicator Light
ON
OFF
ADVANCE PROGRAMMABLE ICE CREAM MIXE
Figure 5
ON
OFF
Press
Figure 6
Make sure the power is ON. Move the cup
continue
The