Explanation Of Type-Identifying Marking And Symbols; Preconditions For Use; Preparation For Use; Preparations Before First Use - Dräger X-plore 8000 Instrucciones De Uso

3.6 Explanation of type-identifying
marking and symbols
The name plate shown is an example. The specifications vary
depending on the facepiece.
1
X-plore 8000 Helmet with visor
2
EN 397:2012+A1:2012 LD -30°C +150°C MM 440V a.c.
EN 166:2001 1 BT 9 3, EN 352-3:2002
2797
EN 12941:1998+A1:2003 +A2:2008 TH3/TH1 *
* in combination with chinseal
EN 14594:2018 Class 3B
0158
ANSI/ISEA Z89.1 Type 1 Class G
ANSI/ISEA Z87+ 2015
ANSI/ISEA S3.19-1974
SAI Global
AS/NZS 1716:2012
Lic No SMK1346
AS/NZS 1801:1997 TYPE 1
SAFETY WARNING:
HELMET MUST BE REPLACED IF DAMAGED
DUE TO SEVERE IMPACT OR DETERIORATION.
DO NOT MODIFY OR REMOVE PARTS.
REPLACE COMPLETE HARNESS ONLY.
HELMET MAY BE SERIOUSLY DAMAGED BY
SUBSTANCES SUCH AS PETROL, PAINT, ADHESIVES,
3
AEROSOL SPRAYS OR CLEANING AGENTS.
Size Range: 52-60.6cm (6
Material PA66
U.S. Patent No. D802,117
4
U.S. Patent No. D788,991
National Institute for
Occupational Safety and Health
®
www.draeger.com
5 Dräger Safety, 23560 Lübeck, Germany
Importer (UK): Draeger Safety UK Ltd., Blyth, UK
3710xxx
6
012345678
2020 - 04
1 Product name
2 Approval marking
3 Size
4 Material
Instructions for use |
Dräger X-plore 8000 Facepieces
0086
in.)
+45°C
< 90% RH
-10°C
Made in USA
5 Distributor
6 REF: Part number
LOT: Batch
Date of manufacture (here:
April 2020)
7 Ambient conditions
8 Symbol "Follow instructions
for use"
4 Use
4.1

Preconditions for use

– Type and concentration of the contaminants must be
known. When checking the conditions of use, also pay
attention to whether additional protective clothing is
required.
– When used with a powered air-purifying respirator, the
oxygen content of the ambient air must not fall below the
following limit values:
● 17 Vol% in Europe excluding Netherlands, Belgium,
UK,
● 19 Vol% in Netherlands, Belgium, UK.
● 19.5 Vol% in the USA.
For other countries, observe national regulations!
4.2

Preparation for use

4.2.1 Preparations before first use

Filters can only be connected to the powered air-purifying
respirator and not directly to the Dräger X-plore 8000
facepieces.
1. Adjust the position of the headband (see "Adjust the
position of the headband", page 17).
2. If necessary, fit earmuffs.
3. Dräger X-plore 8000 helmet/hood combination or bump
8
cap/hood combination:
Attach hood to helmet shell or bump cap shell (see
"Replace the hood", page 17).
7
4. If necessary, remove the transport foil from the visor.
4.2.2 Preparations before every use
WARNING
Scratched or damaged visors or hoods can restrict
visibility or impair the protective effect!
► Replace scratched or damaged visors or hoods.
Filters can only be connected to the blower unit and not
directly to the X-plore 8000 facepieces.
1. Inspect all components of the facepiece for cracks,
deformations or other damage, as well as wear and
correct fit.
2. Replace scratched or damaged parts.
3. If necessary, fit a protective foil.
| en
Use
15