Machine Control Panel - Clarke Focus II Disc 26 Manual De Instrucciones

ENGLISH
EN

MACHINE CONTROL PANEL

Key Switch (See Figure 1, Item "A")
The key switch turns "ON" the power to the control panel. "O" is "OFF" and "I" is "ON".
Traverse Speed Switch (See Figure #1, Item "B")
The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the
speed, turn the knob to the left.
One Touch Control Button (See Figure 1, Item "C")
The one touch control button raises and lowers the brush head assembly, starts and stops the vacuum motor automati-
cally. Press the one touch control button once and the brush head assembly lowers to the floor and the vacuum motor
turns "ON" (brush head and vacuum LEDs illuminate green). The brush motors start when the brushes are down and
the forward palm button is depressed. Press the one touch control button again and the brush head assembly raises,
the vacuum motor will remain on for 10 seconds and then shut "OFF".
Increase Brush Pressure Button (See Figure 1, Item D)
This button is used to increase the brush pressure. Increased brush pressure may be required when stripping or
cleaning heavily soiled floors. To increase brush pressure, first lower the brushes by pressing the one touch control
button (Item "C"). This will lower the brushes to the normal scrub position. To increase brush pressure, press the
button (Item "D"). The LED above the button will illuminate yellow. Press the button (Item "D") again and the brushes
will return to normal scrub (yellow LED will turn "OFF"). NOTE: Increase brush pressure is not available on cylindrical
machine.
Vacuum Motor Button (See Figure 1, Item "E")
The vacuum motor button turns the vacuum motor "ON" or "OFF", regardless of brush head assembly position. The
green LED will illuminate when the vacuum motor is "ON".
Solution Control Buttons (See Figure 1, Item "F & G")
The solution control buttons regulate the flow of cleaning solution to the floor. The normal scrub solution setting is
indicated by two green bars on the meter. On cylindrical machines, with most floor conditions, the solution setting
should be set one step higher. To increase the flow, press the solution flow button "G" (+) until the desired flow is
reached. To decrease the flow, press the solution flow button "F" (-) until the desired flow is reached. To shut off the
solution, press the solution flow button "F" (-) until no indicators are visible on the display. NOTE: No solution will flow
when the machine does not traverse.
Forward Palm Buttons (See Figure 1, Item "H")
The forward palm buttons turn the traverse motor "ON" and if the brush motors are in the down position, it also activates
the brush motors and solution control module. Either the right or the left palm button can be used.
Reverse Push Button (See Figure 1, Item "I")
The reverse push button, when used in conjunction with one of the forward palm buttons, causes the machine to reverse
direction. The reverse speed is 67% of the forward speed.
Charge / Battery Meter (See Figure 1, Item "J")
The charge / battery meter indicates the battery is being charged when the charger is plugged into an AC outlet. It also
indicates the amount of charge that is left in the batteries while the machine is in use. When the charge gets too low the
brush/pad motors will shut off.
Circuit Breakers (See Figure 1, Item "K & L")
The circuit breakers for the brush motors are located on the control panel. If a circuit breaker trips, determine which
motor is not operating and turn the key switch "OFF". Wait five minutes and push the reset button back in. Turn the key
switch "ON", and try again. An authorized service person should be contacted if the breaker trips again.
Hour Meter (Optional) (See Figure 1, Item "M")
The hour meter indicates the number of hours the machine has operated. It runs only when the machine is moving
forward or reverse.
Chemical Mixing Control (Optional) (See Figure 1, Item "N")
The chemical mixing control regulates the amount of concentration of cleaning chemical mixed with the clear water from
the solution tank. Turning the chemical mixing knob clockwise increases the concentration of chemical.
®
Clarke
-8- Operator's Manual (EN) - FOCUS II MID-SIZE AUTOSCRUBBER ®