Parameter List - Galletti MYCOMFORT LARGE Manual Del Usuario

MYCOMFORT LARGE

PARAMETER LIST

Time schedules are programmed by setting the individual parameters encountered
when scrolling with the arrow keys.
Warning: there are a total of 37 parameters, but not of all them are accessible. Whether
certain parameters will be displayed or not depends on the value assigned to the first
parameter (H00), i.e. the operating mode selected. More specifically:
GB
- if H00=1 (ON/OFF mode), parameters H18 to H29 will not be displayed
- if H00=2 (operation based on temperature SETPOINT), parameters H12 to H17
will not be displayed
- if H00=0, the time programming function is disabled and therefore no parameter
will be displayed except for H00
Below is a description of all 37 parameters, in sequence.
- H00 =ENABLING AND OPERATING MODES
> H00=0 : scheduling disabled
> H00=1 : ON/OFF time schedules
> H00=2 : time schedules based on temperature SETPOINT
CLO:
- H01 =HOUR of controller clock
- H02 = MINUTES of controller clock
DAY:
- H03 =DAY OF THE WEEK
Hr1:
- H04 =OUR (0-23) of SCHEDULE 1
- H05 =MINUTES (0-59) of SCHEDULE 1
Hr2:
- H06 = HOUR (0-23) of SCHEDULE 2
- H07 =MINUTES (0-59) of SCHEDULE 2
Hr3:
- H08 =OUR (0-23) of SCHEDULE 3
- H09 =MINUTES (0-59) of SCHEDULE 3
Hr4:
- H10 = HOUR (0-23) of SCHEDULE 4
- H11 =MINUTES (0-59) of SCHEDULE 4
- H12 = STATUS (ON or OFF) of TIME SLOT 1
- H13 = STATUS (ON or OFF) of TIME SLOT 2
- H14 = STATUS (ON or OFF) of TIME SLOT 3
- H15 = STATUS (ON or OFF) of TIME SLOT 4
- H16 = STATUS (ON or OFF) of TIME SLOT 5
- H17 = STATUS (ON or OFF) of TIME SLOT 6
SP1:
- H18 = SUMMER temperature SETPOINT of TIME SLOT 1
SP2:
- H19 = SUMMER temperature SETPOINT of TIME SLOT 2
SP3:
- H20 = SUMMER temperature SETPOINT of TIME SLOT 3
SP4:
- H21 = SUMMER temperature SETPOINT of TIME SLOT 4
SP5:
- H22 = SUMMER temperature SETPOINT of TIME SLOT 5
SP6:
- H23 = SUMMER temperature SETPOINT of TIME SLOT 6
SP1:
- H24 = WINTER temperature SETPOINT of TIME SLOT 1
SP2:
- H25 = WINTER temperature SETPOINT of TIME SLOT 2
SP3:
- H26 = WINTER temperature SETPOINT of TIME SLOT 3
FC66002638 - rev. 05
È severamente vietata la riproduzione anche parziale di questo manuale / All copying, even partial, of this manual is strictly forbidden
SP4:
- H27 = WINTER temperature SETPOINT of TIME SLOT 4
SP5:
- H28 = WINTER temperature SETPOINT of TIME SLOT 5
SP6:
- H29 = WINTER temperature SETPOINT of TIME SLOT 6
Mon:
- H30 = daily profile (1 or 2) for MONDAY
Tue:
- H31 = daily profile (1 or 2) for TUESDAY
Wed:
- H32 = daily profile (1 or 2) for WEDNESDAY
Thu:
- H33 = daily profile (1 or 2) for THURSDAY
Fri:
- H34 = daily profile (1 or 2) for FRIDAY
Sat:
- H35 = daily profile (1 or 2) for SATURDAY
Sun:
- H36 = daily profile (1 or 2) for SUNDAY
- H37 = 24H or 12H display
DEFAULT VALUES OF PARAMETERS
- H00 =0 (scheduling disabled)
- Hr1 = 06:00
- Hr2 = 22:00
- Hr3 = 08:00
- Hr4 = 20:00
- H12 = OFF
- H13 = ON
- H14 = OFF
- H15 = OFF
- H16 = ON
- H17 = OFF
- H18-H23 = 25°C
- H24-H29 = 22°C
- H30-H34 = 1
- H35-H36 = 2
- H37 = 24H
If the 12H display mode has been set (parameter H37), for configuration parameters
H01 to H11 (except H03) the display will not show the sequential number of the
parameter but rather the hourly situation expressed in AM/PM.
DISPLAY
If the time programming function is enabled, when the thermostat is on the clock
symbol will always appear and it will be possible to check whether the time settings
are correct (only for a few instants) by simultaneously pressing the SEL+MODE
buttons. When the thermostat is off, the clock symbol and current hour will appear
constantly on the display only if the ON/OFF time programming mode is enabled.
ALARMS
This control governs two types of alarms:
- Serious Alarms cause the forced switching off of the thermostat
- Non-serious Alarms do not cause the forced switching off of the thermostat, but
disable possible critical functions
46