Additional Safety Rules For Mitre Saws - BTI PS 1800+ Manual Del Usuario

19 . Stay alert.
Watch what you are doing. Use common sense. Do not
operate the tool when you are tired or under the influence of
drugs or alcohol.
20 . Check for damaged parts.
Before use, carefully check the tool and mains cable to
determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting and
any other conditions that may affect its operation. A guard
or other part that is damaged should be properly repaired
or replaced by an authorized service centre unless otherwise
indicated in this instruction manual. Have defective switches
replaced by an authorized service centre. Do not use the tool
if the switch does not turn it on and off. Never attempt any
repairs yourself.
WARNING! The use of any accessory or attachment or
performance of any operation with this tool other than
those recommended in this instruction manual may
present a risk of personal injury.
21 . Have your tool repaired by a qualified person.
This electric tool complies relevant safety rules. Repairs should
only be carried out by qualified persons using original spare
parts; otherwise this may result in considerable danger to
the user.

Additional Safety Rules for Mitre Saws

• The machine is provided with a special configured power
supply cord which can only be replaced by the manufacturer
or its authorised service agent.
• Do not use the saw to cut other materials than those
recommended by the manufacturer.
• Do not operate the machine without guards in position, or if
guards do not function or are not maintained properly.
• Ensure that the arm is securely fixed when performing
bevel cuts.
• Keep the floor area around the machine level, well-
maintained and free of loose materials, e.g., chips and cut-
offs.
• Select the correct blade for the material to be cut.
• Use correctly sharpened saw blades. Observe the maximum
speed mark on the saw blade.
• Make sure all locking knobs and clamp handles are tight
before starting any operation.
• Never place either hand in the blade area when the saw is
connected to the electrical power source.
• Never attempt to stop a machine in motion rapidly by
jamming a tool or other means against the blade; serious
accidents can occur.
• Before using any accessory consult the instruction manual.
The improper use of an accessory can cause damage.
• Use a holder or wear gloves when handling a saw blade or
rough material.
• Ensure that the saw blade is mounted correctly before use.
• Make sure that the blade rotates in the correct direction.
• Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the
technical data. Use only the blades specified in this manual,
complying with EN847-1.
• Consider applying specially designed noise-reduction blades.
• Do not use HIGH SPEED STEEL blades.
• Do not use cracked or damaged saw blades.
• Do not use any abrasive or diamond discs.
• Use only saw blades where the marked speed is at least equal
to the speed marked on the saw.
• Never use your saw without the kerf plate.
• Raise the blade from the kerf in the workpiece prior to
releasing the switch.
• Before each cut ensure that the machine is stable.
• Do not wedge anything against the fan to hold the
motor shaft.
• The blade guard on your saw will automatically raise when
the arm is brought down; it will lower over the blade when
head lock up release lever
• Never raise the blade guard manually unless the saw is
switched off. The guard can be raised by hand when installing
or removing saw blades or for inspection of the saw.
• Check periodically that the motor air slots are clean and free
of chips.
• Replace the kerf plate when worn.
• Disconnect the machine from the mains before carrying out
any maintenance work or when changing the blade.
• Never perform any cleaning or maintenance work when
the machine is still running and the head is not in the
rest position.
• When fitted with LED, no exchange with different type
of LED permitted. Repairs shall only be carried out by the
manufacturer or an authorized agent.
• Connect the saw to a dust collection device when sawing
wood. Always consider factors which influence exposure of
dust such as:
- type of material to be machined (chip board produces
more dust than wood);
- sharpness of the saw blade;
- correct adjustment of the saw blade,
- dust extractor with air velocity not less than 20 m/s.
Ensure that the local extraction as well as hoods, baffles and
chutes are properly adjusted.
• Please be aware of the following factors influencing exposure
to noise:
- use saw blades designed to reduce the emitted noise;
- use only well sharpened saw blades;
• Machine maintenance shall be conducted periodically;
• Provide adequate general or localized lighting;
• Ensure the operator is adequately trained in the use,
adjustment and operation of the machine;
• Ensure that any spacers and spindle rings are suitable for the
purpose as stated in this manual.
ENGLISH
2 is pushed.
31