Electrical Safety - BTI PS 1800+ Manual Del Usuario

This unit is designed for use with a nominal blade diameter
216 mm carbide tip blade.
DO NOT use under wet conditions or in presence of flammable
liquids or gases.
These miter saws are professional power tools.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
WARNING! Do not use the machine for purposes other
than intended.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for
their safety. Children should never be left alone with
this product.

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your tool is double insulated in accordance with
EN61029; therefore no earth wire is required.
In case of cord replacement the tool must only be repaired by
an authorized service agent or by qualified electrician.
The following cords are mandatory:
BTI PS 1800+ : H05RN-F, 2×1.0 mm²
BTI PS 1800+ LX : H05RR-F, 2×1.5 mm²
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug fitted should be comply with BS EN60309 (BS4343),
16 Amps, earthing contact position 4h.
WARNING: Always ensure that the cable clamp is
correctly and securely fitted to the sheath of the cable.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data). The minimum conductor size is 1.5 mm²; the
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
ASSEMBLY
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories, before
adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Unpacking
The motor and guards are already assembled onto the base.
Cable Clamp (Fig. F)
Insert the cable 28 into the cable clamp
cable for the saw head to travel, then tighten the clamp by
means of the screw.
Bench Mounting (Fig. B)
1. Holes 22 are provided in all four feet to facilitate bench
mounting.
Two different sized holes are provided to accommodate
different sizes of bolts. Use either hole; it is not necessary
to use both. Bolts with a diameter of 8 mm and 80 mm
in length is suggested. Always mount your saw firmly to
prevent movement. To enhance the portability, the tool
can be mounted to a piece of 12.5 mm or thicker plywood
which can then be clamped to your work support or moved
to other job sites and reclamped.
2. When mounting your saw to a piece of plywood, make
sure that the mounting screws do not protrude from the
bottom of the wood.
The plywood must sit flush on the work support. When
clamping the saw to any work surface, clamp only on the
clamping bosses where the mounting screw holes are
located. Clamping at any other point will interfere with the
proper operation of the saw.
3. To prevent binding and inaccuracy, be sure the mounting
surface is not warped or otherwise uneven. If the saw rocks
on the surface, place a thin piece of material under one saw
foot until the saw is firm on the mounting surface.
Mounting the Saw Blade (Fig. A, G–I)
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories, before
adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.
WARNING: The teeth of a new blade are very sharp and
can be dangerous.
WARNING: Be aware the saw blade shall be replaced in
the described way only. Only use saw blades as specified
under Technical Data; Cat.no.: DT4320 is suggested.
ENGLISH
27 . Allow enough
33