EN
For Use With
This section identifies components intended to be used
with the equipment to obtain a safe combination.
WARNINGS:
▪ Use only Stryker-approved equipment, unless
otherwise specified.
▪ Use of unapproved electrical equipment may result
in increased electromagnetic emissions or decreased
electromagnetic immunity of the system.
NOTE: For a complete list of components or ordering
information, contact your Stryker sales representative or
call Stryker customer service. See the Contact Information
section. Outside the US, contact your nearest Stryker
subsidiary.
Power and Care Components
Description
STRYKER SYSTEM G Transfer
Shield
STRYKER SYSTEM G Power
Module
STRYKER SYSTEM G Charger,
2-Bay
STRYKER SYSTEM G Sterilization
Cases
Attachments and Cutting and
Fixation Tools
WARNING: All cutting and fixation tools are intended
for single use only.
Wire and Pin Collets
NOTE: Wire and pin collets REF 4103-063-000, 4103-
126-000S3, and 4103-126-000 are not compatible with
STRYKER SYSTEM G.
Attachment
REF
STRYKER
7307-001-000
SYSTEM G
Wire Collet
STRYKER
7307-002-000
SYSTEM G Pin
Collet, Small
STRYKER
7307-003-000
SYSTEM G Pin
Collet, Large
4
REF
7304-120-000
7309-120-000
7310-120-000
7302-120-000
7302-130-000
Tools
Kirschner wires and
Steinmann pins
from 0.7 to 1.8 mm
in diameter
Kirschner wires and
Steinmann pins
from 2.0 to 3.2 mm
in diameter
Kirschner wires and
Steinmann pins
from 3.0 to 4.2 mm
in diameter
Keyed Chucks
NOTE: Each chuck is supplied with a chuck key (REF
1331-001-009)
Attachment
REF
1:1 1/4 inch
4103-131-000
(6.4 mm) Keyed
Chuck
High Torque 1/4
4103-180-000
inch (6.35 mm)
Drill with Chuck
2:1 with Key
3.25:1 1/4 inch
4103-231-000
(6.4 mm) Keyed
Chuck
Keyless Chucks
NOTE: The Keyless Chuck Adaptor (REF 4103-082-131) is
intended for use with standard Trinkle attachments.
Attachment
REF
Keyless Chuck
4103-082-131
Adaptor
Keyless Drill
4103-133-000
Attachment
Drill Attachments
Attachment
REF
1:1 AO Small
4103-110-000
Drill
1:1 Hudson
4103-113-000
1:1 Hudson/
4103-135-000
Modified Trinkle
1:1 Trinkle
4103-160-000
7305-001-700 Rev-A
Tools
Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Tools
Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Wires, pins, drill bits,
and tools up to 6.4
mm in diameter
Tools
Drill bits, taps,
automatic
screwdrivers, and
tools with AO snap-
lock shanks
Drill bits, reamers,
taps, automatic
screwdrivers, and
tools with Hudson
fittings
Drill bits, reamers,
automatic
screwdrivers, and
tools with Hudson
or modified Trinkle
fittings
Drill bits, reamers,
automatic
screwdrivers, and
tools with standard
Trinkle fittings
www.stryker.com