3M DBI-SALA FlexiGuard M100 Manual Del Usuario página 6

;
Before using this equipment, record the product identification information from the ID label in the "Inspection and
Maintenance Log" at the back of this manual.
;
Always ensure you are using the latest revision of your 3M instruction manual. Visit the 3M website or contact 3M
Technical Services for updated instruction manuals.
System Specifications:
Capacity:
Compatability:
Maximum Deflection:
Maximum Arresting Force:
Weight:
Supporting Structure:
Standards:
Component Specifications:
Figure 1
Reference
A
M100–Rail Bracket
B
M100–Upright Bracket
C
M100–Winch Mount
1.0 PRODUCT APPLICATION
1.1 PURPOSE: The Jib Boom Rescue Kit adds rescue capabilities to either the M100 or M200 Jib Systems.
1.2 SUPERVISION: Installation of this equipment must be supervised by a Qualified Person
supervised by a Compentent Person
1.3 TRAINING: It is the responsibility of users of this equipment to understand these instructions and be trained in correct
installation, use, and maintenance of this equipment. Users must be aware of the consequences of improper installation
or use of this equipment. This instruction manual is not a substitute for a training program. Training must be provided on
a periodic basis to ensure user proficiency.
1.4 RESCUE PLAN: When using this equipment and connecting subsystem(s), the employer must have a rescue plan and
the means at hand to implement and communicate that plan to users, authorized persons
site rescue team is recommended. Team members should be provided with the equipment and techniques to perform a
successful rescue. Training should be provided on a periodic basis to ensure rescuer proficiency.
1.5 AFTER A FALL: If the system is subjected to fall arrest or impact force, remove the system from service immediately.
Clearly tag the system "DO NOT USE." See Section 4 for more information.
2.0 INSTALLATION
2.1 PLANNING: Plan your Fall Protection system prior to installation of the Rescue Kit. Account for all factors that may affect
your safety before, during, and after a fall. Consider all requirements, limitations, and specifications defined in Table 1 and
the user instructions for the M100 or M200 Jib Boom and bases.
2.2 INSTALLING THE RESCUE KIT: Figure 2 illustrates installation of the Rescue Kit on both the M100 and M200 Jib Boom.
To install the Rescue Kit:
1. Install the Winch Mount on the Jib Mast: Fasten the Winch Mount (B) to the Mounting Plates (A) on the Jib Mast
with the provided 3/8" hardware. Torque hardware to 45 ft-lb (61 N-m).
2. Install the Upright Bracket on the Jib Mast: Fasten the Upright Bracket (A) to the Mounting Plate (B) on the Jib
Mast with the provided 1/2" hardware. Ensure the Upright Bracket (A) is facing away from the rail as shown above.
Torque hardware to 60 ft-lb (81 N-m).
3. Install the Rail Bracket on the Jib Boom:
8530885: Fasten the Rail Bracket (A) to the desired Mounting Holes (B) on the Rail Backbone using the 1/2"
hardware provided. Torque hardware to 45 ft-lb (61 N-m).
8530905: Slide on and fasten the Rail Bracket (A) around the Rail Backbone (B) using the (4x) Clamping Screws (C),
leaving a minumum of 2 in. (5 cm) of space at the end of the rail. The Rail Bracket can be mounted anywhere along
Table 1 – Specifications
Maximum personnel capacity of 1 person with a combined weight (clothing, tools, etc.) of no more than
310 lb. (140 kg).
8530885 is compatible with 3M™ DBI-SALA® Flexiguard™ Modular Jib System M100 and 8530905 is
compatible with 3M™ DBI-SALA® Flexiguard™ Modular Jib System M200. See IFU 5908371 and 5908372
for more information on use of jib systems.
Refer to the instruction manual for the M100 and M200 Jib Booms (5908371, 5908372) for more
information on maximum system deflection.
All connecting subsystems (SRDs, Energy Absorbing Lanyards, etc.) used with the Jib Boom must limit
the Maximum Arresting Force to 1,350 lbf (6 kN).
8530885 Kit - 25 lb. (11 kg)
8530905 Kit - 55 lb. (25 kg)
See user instructions for the 3M Modular Jib Base that is being used.
Designed and tested to OSHA 1926.502 and OSHA 1910.140
8530885 Kit
Components
.
2
8530905 Kit
Components
M200–Rail Bracket
M200–Upright Bracket
M200–Winch Mount
6
Materials
Powder Coated Steel,
Plastic Pulley
Powder Coated Steel,
Plastic Pulley
Powder Coated Steel,
Plastic Pulley
. Use of this equipment must be
1
, and rescuers . A trained, on-
3 4