Attaching The Grass Collector (05); Charging The Rechargeable Battery (06); Operation; Switching The Appliance On/Off (07) - AL-KO GS 7,2 Li Multi Cutter Instrucciones De Instalación

GB
4. Let the unlocking knobs (04/1) engage. The
engaging of the cutting blade must be clearly
audible.
4.1.3

Attaching the grass collector (05)

For using the grass cutter on the edge of a gar-
den bed, the grass collector can be attached to
the grass blade. It straightens up the grass and
prevents the cut-off grass from falling into the
bed.
1. Put the grass collector (05/1) on the under-
side of the grass blade so that the two pins
(05/2) point towards the openings and the
screw lies in the slotted hole (05/3).
2. Push the grass collector (05/1) into the two
openings (05/a) with low pressure.
4.2

Charging the rechargeable battery (06)

Fully charge the rechargeable battery before us-
ing it for the first time. The rechargeable battery
can be charged in any charge state. Interrupting
charging does not damage the rechargeable bat-
tery.
■
The handle of the appliance can become hot
during the charging process. This is normal.
■
Do not use the appliance during the charging
process.
1. Insert the mains plug (06/1) into the power
socket.
2. Insert the charge plug in the charging socket
of the rechargeable battery grass and shrub
cutter (06/3). The charging process begins
with the constant lighting of the green LED
display (06/2) on the mains plug. The LED in-
dicates that current is flowing. The charging
process is indicated by the LED on the appli-
ance (06/4): The rechargeable battery is fully
charged when the LED on the appliance
(06/4) lights constantly.
3. Unplug the mains plug (06/1) from the power
socket and from the charging socket (06/3).

5 OPERATION

5.1

Switching the appliance on/off (07)

Switching on the appliance
1. Push the unlocking knob (07/1) forwards (07/
a).
2. Press the On/Off switch (07/2) at the same
time.
3. Release the unlocking knob (07/1) again
while pressing and holding the On/Off switch
(07/b).
24
Switching off the appliance
WARNING! Danger of lacerations. The
cutting blades continue to run after switching off
the engine.
■
Never reach directly into moving appliance
parts after switching off the appliance.
■
Wait until the cutting blade come to a stand-
still before changing it or cleaning the appli-
ance of cuttings.
■
Wear protective gloves.
1. Release the On/Off switch (07/2).
2. Put the appropriate blade guard on the re-
spective cutting blade.
5.2

Using the grass collector (02)

If you would like to use the grass cutter on the
edge of a bed or on a stone edge, it is recom-
mended to attach the grass collector (see see
chapter 4.1.3 "Attaching the grass collector (05)",
page 24).

6 MAINTENANCE AND CARE (08)

CAUTION! Risk of injury. Sharp-edged
and moving appliance parts can lead to injury.
■
Always wear protective gloves during mainte-
nance, care and cleaning work.
■
After cutting work, thoroughly clean the appli-
ance and the cutting blades with a hand
brush (08/1) or cloth (08/2).
■
Remove any soiling from the gear housing.
■
Treat the cutting blades with oil or care spray
(08/3) after every use. For better distribution
of the oil, switch on the appliance briefly.
■
Check the screw at the bottom of the grass
blade is firmly seated at regular intervals.
■
Do not spray the machine with water. Pene-
trating water can damage the switch as well
as the rechargeable battery and the electric
motor.
■
Check the cutting blade regularly for damage.
Replace blunt or damaged cutting blades be-
fore using the appliance the next time.
■
Lubricate the gear housing regularly with
grease.
■
Professional inspection is required:
■
if there is a blockage of the motor
■
if the cutting blade is bent or damaged
■
if the rechargeable battery is damaged or
leaking
Operation
GS 7,2 Li