Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Contents
• User Safety
• Contents
• Product Overview
• Keypad, Modes, and LED
• Applications
• Batteries and Power
• Set Up
• Operation
• Accuracy Check and Calibration
• Specifications
User Safety
WARNING:
• Carefully read the Safety Instructions and Product
Manual before using this product. The person
responsible for the instrument must ensure that all
users understand and adhere to these instructions.
CAUTION:
• While the laser tool is in operation, be careful not
to expose your eyes to the emitting laser beam
(red light source). Exposure to a laser beam for an
extended time may be hazardous to your eyes.
CAUTION:
• Glasses may be supplied in some of the laser tool
kits. These are NOT certified safety glasses. These
glasses are ONLY used to enhance the visibility of
the beam in brighter environments or at greater
distances from laser source.
Retain all sections of the manual for future reference.
WARNING:
• The following label samples are placed on your laser
tool to inform of the laser class for your convenience
and safety. Please reference the Product Manual
for the specifics on a particular product model.
8
L A S E R R A D I AT I O N - D O N O T
S TA R E I N T O T H E B E A M
C L A S S 2 L A S E R P R O D U C T
Max Output ≤ 1 mW @ 630-680 nm
IEC/EN 60825-1
Complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007.
Product Overview
Figure A - Laser Tool
1. 1/4-20 threaded mount
2. Laser Window
3. Power /Pendulum Lock Switch
4. Slots for Quick Link Bracket Connect
5. LED/Out-of-Level Indicator
Figure B - Laser Tool Battery Location
6. 2 x AA Batteries
7. Battery Cover
Figure C - Power /Transport Lock
Figure D - Laser Modes
Figure E - Quick Link Bracket Assembly.
9. QuickLink Bracket
Figure F - Quick Link™ Bracket Detail
Figure M - Vertical Beam Accuracy
Figure N - Horizontal Beam Accuracy
STHT77342
Keypad, Modes, and LED
Keypad /Switch
(See figure
)
C
Power On/Pendulum lock off /Self-leveling On
Power Off/Pendulum lock on /Self-leveling Off
Modes
(See figure
)
D
Laser Beam Available Modes
•
Horizontal & Plumb, Dot Beams Only
Unlocked /Self-Leveling (See figures
)
C
•
Power is ON, pendulum lock is OFF
and laser unit is
within self-leveling range.
Locked /Self-Leveling (See figures
)
C
•
Power is OFF , pendulum lock is ON.
.
LEDs
(See figure
)
A
Out of level LED - Solid RED
•
Unit is out of level
QuickLink™ Bracket Overview
Figure F - QuickLink™ Bracket
10. T-nut to mate with slots on Laser Unit.
11. Jaw Tightening Knob.
12. Bracket Tightening Knob .
13. Hang holes for screw mounting. (34 mm apart)
14. 1/4-20" threaded mount.
15. Adjustable Jaw
Bracket Applications
• The QuickLink bracket can be mounted in various
positions by clamping the jaws to round or flat objects
such as a tripod pole, door or bench and tightening the
knobs. (See figure
: #11 & #12)
F
STHT77342
• The QuickLink bracket can be mounted on a
vertical surface using the hang holes provided.
(See figure
#13)
F
• The QuickLink bracket can be attached to the bottom
of the laser unit using the 1/4-20" threaded mount
(Figure
#14 and figure
#1) or the t-nut and slot
F
A
connection.
Batteries and Power
Battery Installation / Removal
(See figure
)
B
Laser Tool
• Turn laser tool to bottom. Open battery compartment
cover by pressing and sliding out.
• Install / Remove batteries. Orient batteries correctly
when placing into laser tool.
• Close and lock battery compartment cover by sliding in
until securely closed.
WARNING:
• Pay close attention to the battery holder's (+)
and (-) markings for proper battery insertion.
Batteries must be of same type and capacity.
Do not use a combination of batteries with
different capacities remaining.
9
Publicidad
Tabla de contenido
