Fixer Correctement Le Panneau De Commande Aux Pieds De Support Avant; Fixation De La Barre D'appui; Montage Des Panneaux De Support - Pit Boss PBV3G1 Montaje Y Operación

1 x Lower Smoker Cabinet with
1 x Right Front Leg (#22)
1 x Left Front Leg (#21)
2 x #10-24*1/2"Screw (#C)
2. FIXER CORRECTEMENT LE PANNEAU DE COMMANDE AUX
Installation:
PIEDS DE SUPPORT AVANT
pre-assembled on the Control
Pièces nécessaires :
Cabinet
2 x Vis (#C)
Assembly (#14) using 2 x #10-24*1/2"Screws
(#C) and re-tighten 2 screws on the Control
Installation :
Fig.2.1 shown.
• Près du panneau de commande, desserrez les deux vis reliant le
panneau avant à l'armoire principale.
• À l'aide de deux autres vis, fixez les côtés du panneau avant aux pieds
de support orientés vers l'avant. Une fois ces vis serrées, resserrez les
deux vis précédemment desserrées.
3. MOUNTING BACK SUPPORT TUBE TO

3. FIXATION DE LA BARRE D'APPUI

Pièces nécessaires :
1 x Barre d'appui (#15)
Parts Required:
4 x Vis (#C)
1 x Back Support Tube (#23)
1 x Right Rear Leg with Wheel Assembly (#18)
1 x Left Rear Leg with Wheel Assembly (#20)
Installation :
4 x #10-24*1/2"Screw (#C)
• Installez le support à l'arrière de l'unité entre les deux pieds de support
Installation:
arrière. Fixez en utilisant deux vis de chaque côté. Assurez-vous que le
support est placé sur le dessous de l'armoire principale, vers l'intérieur.
• Mount Back Support Tube (#23) to the Right
Regardez l'illustration pour assembler les supports.
Rear Leg with Wheel Assembly (#18) and Left
Rear Leg with Wheel Assembly (#20)using 4 x
#10-24*1/2"Screws (#C)as Fig.3 shown.

4. MONTAGE DES PANNEAUX DE SUPPORT

Pièces nécessaires :
2 x Panneaux de support (#20)
8 x Vis (#C)
Installation :
• Installez un panneau de support sur le côté de l'unité entre un pied
de support avant et un arrière. Fixez en utilisant deux vis de chaque
côté. Assurez-vous que le côté plat de la plaque de support est orienté
vers l'extérieur. Répétez le même processus pour assembler les autres
panneaux de support. Regardez l'illustration pour assembler les
panneaux de support.
36
rews which were
mount Right Front Leg (#22)
2. MOUNTING BOTH FRONT LEGS TO
LOWER CABINET WITH CONTROL
PANEL ASSEMBLY
Parts Required:
1 x Lower Smoker Cabinet with
1 x Right Front Leg (#22)
1 x Left Front Leg (#21)
2 x #10-24*1/2"Screw (#C)
Installation:
pre-assembled on the Control
Cabinet
Assembly (#14) using 2 x #10-24*1/2"Screws
(#C) and re-tighten 2 screws on the Control
RIGHT REAR LEG WITH WHEEL
ASSEMBLY AND LEFT REAR LEG WITH
Fig.2.1 shown.
WHEEL ASSEMBLY
3. MOUNTING BACK SUPPORT TUBE TO
RIGHT REAR LEG WITH WHEEL
ASSEMBLY AND LEFT REAR LEG WITH
WHEEL ASSEMBLY
Parts Required:
1 x Back Support Tube (#23)
1 x Right Rear Leg with Wheel Assembly (#18)
1 x Left Rear Leg with Wheel Assembly (#20)
4 x #10-24*1/2"Screw (#C)
Installation:
• Mount Back Support Tube (#23) to the Right
Rear Leg with Wheel Assembly (#18) and Left
Rear Leg with Wheel Assembly (#20)using 4 x
#10-24*1/2"Screws (#C)as Fig.3 shown.
Installation:
Front Leg (#22)
#10-24*1/2"Screws (#C) as Fig.4 shown.
Leg (#21)
Assembly (#20) using 4 x
#10-24*1/2"Screws (#C) as Fig.4 shown.
5. MOUNTING BURNER CHAMBER
ASSEMBLY TO THE BOTTOM AREA OF
LOWER SMOKER CABINET ASSEMBLY
Parts Required:
1 x Burner Chamber Assembly (#24)
1 x Lower Smoker Cabinet with Control
Panel Assembly (#14)
4 x #10-24*1/2"Screw (#C)
Installation:
• Attach ignition wire onto the pin end of
the Igniter on Control Panel.
Mount Burner Chamber Assembly (#24) to
the bottom area of Lower Smoker Cabinet
with Control Panel Assembly (#14) using 4
x #10-24*1/2"Screws (#C) as Fig.5.1 &
Fig.5.2 shown.
Note: Turn the Lower Smoker Cabinet with
Control Panel and Legs Assembly Right
Side Up as Fig.5.3 shown and tighten all
screws now.
2
to
rews which were
to
mount Right Front Leg (#22)
3
4
7
7
15
20
20
Note: MUST make sure
that the tip of the valves
are completely INSIDE
the end opening of the
Burner Tubes.