Securing The Support Bar; Mounting The Support Panels - Pit Boss PBV3G1 Montaje Y Operación

1 x Lower Smoker Cabinet with
1 x Right Front Leg (#22)
1 x Left Front Leg (#21)
2 x #10-24*1/2"Screw (#C)
2. SECURE CONTROL PANEL TO FRONT SUPPORT LEGS
Installation:
Parts Required:
pre-assembled on the Control
2 x Screw (#C)
Cabinet
Assembly (#14) using 2 x #10-24*1/2"Screws
Installation:
(#C) and re-tighten 2 screws on the Control
• Near the Control Panel, loosen the two screws connecting the front
Fig.2.1 shown.
panel to the main cabinet.
• Using another two screws, secure the front panel sides to the front-
facing support legs. Once these screws are tight, re-tighten the two
screws that were previously loosened.

3. SECURING THE SUPPORT BAR

3. MOUNTING BACK SUPPORT TUBE TO
Parts Required:
1 x Support Bar (#15)
4 x Screw (#C)
Parts Required:
1 x Back Support Tube (#23)
Installation:
1 x Right Rear Leg with Wheel Assembly (#18)
1 x Left Rear Leg with Wheel Assembly (#20)
• Install the Support Bar to the rear of the unit between the two rear
4 x #10-24*1/2"Screw (#C)
Support Legs. Secure using two screws on each side. Ensure the Support
Installation:
Bar is place on the underside of the main cabinet, facing inwards. Note
illustration for Support Bar arrangement.
• Mount Back Support Tube (#23) to the Right
NOTE: The Support Bar with two holes along the bottom should be
Rear Leg with Wheel Assembly (#18) and Left
on the same side of the unit as the power cord exits the Control
Rear Leg with Wheel Assembly (#20)using 4 x
#10-24*1/2"Screws (#C)as Fig.3 shown.
Panel (left side). This is important for later steps.

4. MOUNTING THE SUPPORT PANELS

Parts Required:
2 x Support Panel (#20)
8 x Screw (#C)
Installation:
• Install one Support Panel to the side of the unit between a front and
back support legs. Secure using two screws on each side. Ensure the
flat side of the Support Panel is facing outwards. Repeat the same
installation to mount the other support panel. Note illustration for
Support Panel arrangement.
8
rews which were
mount Right Front Leg (#22)
2. MOUNTING BOTH FRONT LEGS TO
LOWER CABINET WITH CONTROL
PANEL ASSEMBLY
Parts Required:
1 x Lower Smoker Cabinet with
1 x Right Front Leg (#22)
1 x Left Front Leg (#21)
2 x #10-24*1/2"Screw (#C)
Installation:
pre-assembled on the Control
Cabinet
Assembly (#14) using 2 x #10-24*1/2"Screws
(#C) and re-tighten 2 screws on the Control
RIGHT REAR LEG WITH WHEEL
ASSEMBLY AND LEFT REAR LEG WITH
Fig.2.1 shown.
WHEEL ASSEMBLY
3. MOUNTING BACK SUPPORT TUBE TO
RIGHT REAR LEG WITH WHEEL
ASSEMBLY AND LEFT REAR LEG WITH
WHEEL ASSEMBLY
Parts Required:
1 x Back Support Tube (#23)
1 x Right Rear Leg with Wheel Assembly (#18)
1 x Left Rear Leg with Wheel Assembly (#20)
4 x #10-24*1/2"Screw (#C)
Installation:
• Mount Back Support Tube (#23) to the Right
Rear Leg with Wheel Assembly (#18) and Left
Rear Leg with Wheel Assembly (#20)using 4 x
#10-24*1/2"Screws (#C)as Fig.3 shown.
Installation:
Front Leg (#22)
#10-24*1/2"Screws (#C) as Fig.4 shown.
Leg (#21)
Assembly (#20) using 4 x
#10-24*1/2"Screws (#C) as Fig.4 shown.
5. MOUNTING BURNER CHAMBER
ASSEMBLY TO THE BOTTOM AREA OF
LOWER SMOKER CABINET ASSEMBLY
Parts Required:
1 x Burner Chamber Assembly (#24)
1 x Lower Smoker Cabinet with Control
Panel Assembly (#14)
4 x #10-24*1/2"Screw (#C)
Installation:
• Attach ignition wire onto the pin end of
the Igniter on Control Panel.
Mount Burner Chamber Assembly (#24) to
the bottom area of Lower Smoker Cabinet
with Control Panel Assembly (#14) using 4
x #10-24*1/2"Screws (#C) as Fig.5.1 &
Fig.5.2 shown.
Note: Turn the Lower Smoker Cabinet with
Control Panel and Legs Assembly Right
Side Up as Fig.5.3 shown and tighten all
screws now.
2
to
rews which were
to
mount Right Front Leg (#22)
3
4
7
7
15
20
20
Note: MUST make sure
that the tip of the valves
are completely INSIDE
the end opening of the
Burner Tubes.