Denon AVR-3802 Instrucciones De Operación página 14

ENGLISH
7
Select "Yes".
TUNING
BAND MODE
TUNING
8
a. If the "Auto" mode is selected:
Test tones are automatically emitted from the different
speakers.
The test tones are emitted from the different speakers in
the following order, at 4-second intervals the first time and
second time around, 2-second intervals the third time
around and on:
FL C FR
When the surround back speaker setting is set to
"1spkr" for "Speaker Configuration", this is set to "SB".
TUNING
Use the CURSOR buttons to adjust all the speakers to the
same volume.
BAND MODE
The volume can be adjusted between –12 dB and +12 dB in
TUNING
units of 1 dB.
b. When the "Manual" mode is selected
TUNING Use the CURSOR left and right to select the speaker for
which you want to output test tones, then use the
BAND MODE
CURSOR up and down to adjust so that the volume of the
TUNING
test tones from the various speakers is the same.
TUNING
BAND MODE
TUNING
9
After the above settings are completed, press the ENTER button.
ENTER
The "Channel Level" screen reappears.
SHIFT
To cancel the settings, select "Level Clear" and "Yes" on the "Channel Level" screen, then make the
settings again.
The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter
at the listening position.
If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because
adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural
balance.
NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer's
own volume control.
14
All manuals and user guides at all-guides.com
Flashing
Example: When the volume is set to
1spkr
–12 dB while the test tone
SB
is being produced from the
SR SBR SBL SL SW
subwoofer
2spkrs
Flashing
Example: When the volume is set to
–12 dB while the
subwoofer is selected
When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel
level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level
adjustment mode.
After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the
individual surround modes and adjust channel levels that will be remembered for each of those modes.
Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments
for just that mode will be recalled. Check the instructions for adjusting channel levels within each
surround mode on page 27.
You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/7 CH
STEREO, DOLBY/DTS SURROUND, WIDE SCREEN, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO
MOVIE, and MATRIX.
When using either surround speakers A or B, or when using surround speakers A and B at the same time,
be sure to adjust the balance of playback levels between each channel for the various selections of "A
or B" and "A and B".
Setting the Digital In Assignment
• This setting assigns the digital input jacks of the AVR-3802 for the different input sources.
1
At the System Setup Menu select "Digital In Assignment".
TUNING
BAND MODE
TUNING
2
Switch to the Digital In Assignment screen.
ENTER
SHIFT
3
Select the digital input jack to be assigned to the input source.
TUNING
TUNING • To select the input source
• To select the digital input jack
BAND MODE
BAND MODE
Select "OFF" for input sources for which no digital input jacks are used.
TUNING
TUNING
If "Yes" is selected for "Default", the settings are automatically reset
to the default values.
4
Enter the setting.
ENTER
The System Setup Menu reappears.
SHIFT
NOTES:
• The OPTICAL 3 jacks on the AVR-3802's rear panel are equipped with an optical digital output jack for
recording digital signals on a CD recorder, MD recorder or other digital recorder. Use this for digital recording
between a digital audio source (stereo - 2 channel) and a digital audio recorder.
• Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-3802's rear
panel to any jack other than the OPTICAL 3 IN jack.
• "PHONO" and "TUNER" cannot be selected on the Digital In Assignment screen.